Developing lightweight computation at the DSG edge

qmp_functions.sh 24.8 KB
Newer Older
1
#!/bin/sh
2
# requires ip ipv6calc awk sed grep
3
4
5
6
7
8
QMP_PATH="/etc/qmp"
SOURCE_FUNCTIONS=1

#######################
# Importing files
######################
9
10
11
12
13
if [ -z "$SOURCE_OPENWRT_FUNCTIONS" ]
then
	. /lib/functions.sh
	SOURCE_OPENWRT_FUNCTIONS=1
fi
14
15
16
. $QMP_PATH/qmp_common.sh
[ -z "$SOURCE_GW" ] && . $QMP_PATH/qmp_gw.sh
[ -z "$SOURCE_NET" ] && . $QMP_PATH/qmp_network.sh
17
[ -z "$SOURCE_SYS" ] && . $QMP_PATH/qmp_system.sh
18
[ -z "$SOURCE_WIRELESS" ] && . $QMP_PATH/qmp_wireless.sh
19
[ -z "$SOURCE_COMMON" ] && . $QMP_PATH/qmp_common.sh
20
21
22

qmp_get_llocal_for_dev() {
  local dev=$1
23
  ip a show dev $dev | awk '/inet6/{print $2}'
24
25
26
27
28
}

# returns primary device
qmp_get_primary_device() {
  local primary_mesh_device="$(uci get qmp.node.primary_device)"
29
  [ -z "$primary_mesh_device" ] &&
30
31
32
33
34
35
      {
      if ip link show dev eth0 > /dev/null; then
        primary_mesh_device="eth0"
      else
        primary_mesh_device="$(ip link show | awk '!/lo:/&&/^[0-9]?:/{sub(/:$/,"",$2); print $2; exit}')"
      fi
36
      [ -z "$primary_mesh_device" ] && echo "CRITICAL: No primary network device found, please define qmp.node.primary_device"
37
38
39
40
      }
  echo "$primary_mesh_device"
}

41
# check if a device exists
42
43
44
45
qmp_check_device() {
	ip link show $1 1> /dev/null 2>/dev/null
	return $?
}
46

47
48
49
50
51
52
53
# Function qmp_set_vlan()
#
# This function creates a VLAN interface on top of an interface in order to
# isolate the routing protocol traffic there:
#
#  - 802.1 VLANs are used for wireless interfaces.
#  - 802.1ad (QinQ) VLANs are used for wired devices since qMp > 3.2.1
54
qmp_set_vlan() {
55
56
57
  local iface="$1" # The physical interface
  local vid=$2     # The VLAN
  local liface=$3  # The logical interface lan/wan_X/mesh_Y
58

59
60
  echo "Setting VLAN $vid for interface $iface"
  [ -z "$iface" ] || [ -z "$vid" ] && return
61

62
  # Replace dots by underscores to use the interface name as part of another one
63
  local uiface="$(echo $iface | sed -r 's/\./_/g')"
64

65
66
67
68
	uci set network.${uiface}_${vid}=device
	local vtype=""
	# If $dev exists and is not wireless
  if [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ]; then
69
    # 802.1ad VLANs for wired interfaces
70
    uci set network.${uiface}_${vid}.type=8021ad
71
		vtype="ad"
72
		echo "VLAN $vid for interface $iface is of type 802.1ad (QinQ)"
73
  else
74
75
76
77
		# 802.1q VLANs for wireless interfaces
		uci set network.${uiface}_${vid}.type=8021q
		echo "VLAN $vid for interface $iface is of type 802.1q"
		vtype="q"
78
  fi
79

80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
	uci set network.${uiface}_${vid}.name=${uiface}_${vid}
	if [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ]; then
		# VLANs for wired interfaces are configured directly on top of the physical
		# interface (e.g. eth0.2, eth1)
		uci set network.${uiface}_${vid}.ifname=${iface}
	else
		# VLANs for wireless interfaces need to be configured on top of the
		# logical interface the radio is put in (e.g. mesh_w0 for wlan0)
		uci set network.${uiface}_${vid}.ifname='@'${liface}
	fi
	uci set network.${uiface}_${vid}.vid=${vid}

  uci set network.${uiface}_${vid}_${vtype}=interface
  uci set network.${uiface}_${vid}_${vtype}.ifname=${uiface}_${vid}
  uci set network.${uiface}_${vid}_${vtype}.proto=${none}
  uci set network.${uiface}_${vid}_${vtype}.auto=1
96
  uci commit network
97

98
99
100
}

qmp_get_virtual_iface() {
101
102
	local device="$1"
	local viface=""
103

104
	# Is it the br-lan interface?
105
106
107
108
109
110
	if [ "$device" == "br-lan" ]; then
		viface="lan"
		if [ ! -e "/sys/class/net/$device/phy80211" ]; then
			echo $viface
			return
		fi
111
	fi
112

113
	# Is it in the LAN bridge, and not wireless?
114
115
116
	for l in $(qmp_get_devices lan); do
		if [ "$l" == "$device" ]; then
			viface="lan"
117
			if [ ! -e "/sys/class/net/$device/phy80211" ] && ! qmp_is_in "$device" $(qmp_get_wifi_devices); then
118
119
120
				qmp_log "LOG: 5"
				qmp_log "Viface: $viface"
				qmp_log $device $viface
121
				qmp_log $(qmp_get_wifi_devices)
122
123
124
125
126
				echo $viface
				return
			fi
		fi
	done
127

128
129
130
131
132
133
134
135
136
137
138
139
	qmp_log "LOG: 6"
	qmp_log "Viface: $viface"
	qmp_log $device $viface

	[ ! -e "/sys/class/net/$device/phy80211" ] && ! qmp_is_in "$device" $(qmp_get_wifi_devices) && [ -n "$viface" ] && {
		echo $viface;
		qmp_log "LOG: 7"
		qmp_log "Viface: $viface"
		qmp_log $device $viface
		echo "$viface"
		return;
	}
140

141
	# id_char is the first char of the device: [e]th0 [w]lan1a
142
	local id_char=$(echo $device | cut -c 1)
143
144
145
146
	# id_num is the number of the device: eth[0], wlan[1]a
	local id_num=$(echo $device | tr -d "[A-z]" | tr - _ | tr . _)
	# id_extra are the extra characters after the number: eth0[], wlan1[a]
	local id_extra=$(echo $device | sed -e 's/^[a-z]*[0-9]*//g')
147

148
	# It it a WAN device?
149
150
151
	for w in $(qmp_get_devices wan); do
		if [ "$w" == "$device" ]; then
			viface="wan_${id_char}${id_num}"
152
			qmp_log "LOG: 8"
153
154
			qmp_log "Viface: $viface"
			qmp_log $device $viface
155
156
157
158
			echo $viface
			return
		fi
	done
159

160
	# Is it mesh?
161
162
	for w in $(qmp_get_devices mesh); do
		if [ "$w" == "$device" ]; then
163
			viface="mesh_${id_char}${id_num}${id_extra}"
164
			qmp_log "LOG: 8"
165
166
167
168
			qmp_log "Viface: $viface"
			qmp_log $device $viface
			echo "$viface"
			return
169
170
		fi
	done
171
172
173
174
175
176
}

# arg1=<mesh|lan|wan>, returns the devices which have to be configured in such mode
qmp_get_devices() {
  local devices=""

177
  if [ "$1" == "mesh" ]; then
178
179
		devices="$(uci get qmp.interfaces.mesh_devices 2>/dev/null)"
	fi
180
181
182
183
184
185
186
187
188
189
190
191
192

  if [ "$1" == "lan" ]; then
     devices="$(uci get qmp.interfaces.lan_devices 2>/dev/null)"
  fi

  if [ "$1" == "wan" ]; then
     devices="$(uci get qmp.interfaces.wan_devices 2>/dev/null)"
  fi

  echo "$devices"
}


193
# Scan and configure the network devices (lan, mesh and wan)
194
# if $1 is set to "force", it rescan all devices
195
196
197
198
qmp_configure_smart_network() {
	echo "---------------------------------------"
	echo "Starting smart networking configuration"
	echo "---------------------------------------"
199
	local force=$1
200
201
202
203
204
	local mesh=""
	local wan=""
	local lan=""
	local dev=""
	local phydevs=""
205
	local ignore_devs=""
206
207
	local default_lan=$(qmp_get_openwrt_default_network "lan")
	local default_wan=$(qmp_get_openwrt_default_network "wan")
208

209
210
211
	[ "$force" != "force" ] && {
		ignore_devs="$(qmp_uci_get interfaces.ignore_devices)"
	}
212

213
	for dev in $(ls /sys/class/net/); do
214
		[ -e /sys/class/net/$dev/device ] || [ dev == "eth0" ] && {
215
			local id
216
			local ignore=0
217

218
			# Check if device is in the ignore list
219
220
221
222
				for id in $ignore_devs; do
					[ "$id" == "$dev" ] && ignore=1
				done

223
224
225
226
227
228
229
230
231
232
			# [Qin] The device might be a wired device (e.g. eth0) with a switch
			# and two or more virtual switched devices (e.g. eth0.1, eth0.2)
			for sdev in $(ls /sys/class/net/$dev/ | grep upper_$dev. | cut -d "_" -f2); do
				phydevs="$phydevs $sdev\n"
				ignore=1
			done

			if [ $ignore -eq 0 ]; then
				phydevs="$phydevs $dev\n"
			fi
233
		}
234
	done
235
	phydevs="$(echo -e "$phydevs" | grep -v -e ".*ap$" | sort -u | tr -d ' ' \t)"
236

237
238
239
240
241
242
	# if force is not enabled, we are not changing the existing lan/wan/mesh (only adding new ones)
	[ "$force" != "force" ] && {
		lan="$(qmp_uci_get interfaces.lan_devices)"
		wan="$(qmp_uci_get interfaces.wan_devices)"
		mesh="$(qmp_uci_get interfaces.mesh_devices)"
	}
243

244
245
	local j=0
	local mode=""
246
247
	local cnt
	local cdev
248

249
	for dev in $phydevs; do
250
		# If force is enabled, do not check if the device is already configured
251
		[ "$force" != "force" ] && {
252

253
254
			cnt=0
			# If it is already configured, doing nothing
255
			for cdev in $lan; do
256
				[ "$cdev" == "$dev" ] && cnt=1
257
			done
258
			for cdev in $mesh; do
259
				[ "$cdev" == "$dev" ] && cnt=1
260
			done
261
			for cdev in $wan; do
262
				[ "$cdev" == "$dev" ] && cnt=1
263
264
265
			done
			[ $cnt -eq 1 ] && continue
		}
266

267
268
		# If the device is not configured already, assign its role acording to
		# OpenWrt's defaults. This avoids the per-device hooks that swapped roles
269
270
271
272
		for ddev in $default_lan; do
			[ "$dev" == "$ddev" ] && {
				lan="$lan $dev"
				mesh="$mesh $dev"
273
				novlan="$novlan $dev"
274
275
276
277
278
279
280
				continue
			}
		done
		for ddev in $default_wan; do
			[ "$dev" == "$ddev" ] && {
				wan="$wan $dev"
				mesh="$mesh $dev"
281
				novlan="$novlan $dev"
282
283
284
				continue
			}
		done
285

286
287
		# if it is a wifi device (actually, if it is not a non-wifi device)
		! ( [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ] ) && {
288
289
290
291
			j=0
			while qmp_uci_test qmp.@wireless[$j]; do
				[ "$(qmp_uci_get @wireless[$j].device)" == "$dev" ] && {
					mode="$(qmp_uci_get @wireless[$j].mode)"
292
293
					( [ "$mode" == "aplan" ] || [ "$mode" == "80211s_aplan" ] || [ "$mode" == "adhoc_ap" ] ) && lan="$dev $lan"
					( [ "$mode" == "80211s" ] || [ "$mode" == "80211s_aplan" ] || [ "$mode" == "80211s_adhoc" ] || [ "$mode" == "adhoc" ] || [ "$mode" == "adhoc_ap" ] ) && mesh="$dev $mesh"
294
295
296
297
298
					break
				}
				j=$(($j+1))
			done
		} && continue
299

300
		# If it's not wireless nor a default wan/lan, set it to mesh
301
		[ "$dev" != "$default_lan" ] && [ "$dev" != "$default_wan" ] && {
302
			inmesh="0"
303
			innovlan="0"
304
305
306
307
			# A small trick to avoid duplicates when $default_xan = "eth1 eth2" (e.g., APUs)
			for mdev in $mesh; do
				[ "$mdev" == "$dev" ] && inmesh="1"
			done
308
			[ "$inmesh" == "0" ] && mesh="$dev $mesh"
309
310
311
312
313

			for mdev in $novlan; do
				[ "$mdev" == "$dev" ] && innovlan="1"
			done
			[ "$innovlan" == "0" ] && novlan="$dev $novlan"
314
		}
315

316
	done
317

318
	echo "Network devices found:"
319
320
321
	echo "- LAN $lan"
	echo "- MESH $mesh"
	echo "- WAN $wan"
322
	echo "- NO VLAN $novlan"
323

324
	# Writes the devices to the config
325
326
327
	qmp_uci_set interfaces.lan_devices "$(echo $lan | sed -e s/"^ "//g -e s/" $"//g)"
	qmp_uci_set interfaces.mesh_devices "$(echo $mesh | sed -e s/"^ "//g -e s/" $"//g)"
	qmp_uci_set interfaces.wan_devices "$(echo $wan | sed -e s/"^ "//g -e s/" $"//g)"
328
	qmp_uci_set interfaces.no_vlan_devices "$(echo $novlan | sed -e s/"^ "//g -e s/" $"//g)"
329
	qmp_uci_set interfaces.ignore_devices "$ignore_devs"
330
331
}

332
333
334
335
336
337
338
339
340
341
qmp_get_openwrt_default_network() {
	local role=$1
	local board_file="/etc/board.json"
	local flen=$(wc -l $board_file | cut -d " " -f 1)

	[ "$role" != "lan" ] && [ "$role" != "wan" ] && return

	grep -A${flen} "network" $board_file | grep -A${flen} $role | grep -m 1 -B${flen} "}" | grep -m 1 "ifname" | cut -d ":" -f2 | sed -e 's/^[ \t]*//' | cut -d '"' -f 2
}

342
343
qmp_attach_device_to_interface() {
	local device=$1
344
	local interface=$2
345
346
	local intype="$(qmp_uci_get_raw network.$interface.type)"

347
	echo "Attaching device $device to interface $interface"
348
349

	# is it a wifi device?
350
	if qmp_uci_test wireless.$device; then
351
		qmp_uci_set_raw wireless.$device.network=$interface
352
		echo " -> $device wireless attached to $interface"
353
354

	# if it is not
355
	else
356
			if [ "$intype" == "bridge" ]; then
357
				qmp_uci_add_list_raw network.$interface.ifname=$device
358
359
				echo " -> $device attached to $interface bridge"
			else
360
				qmp_uci_set_raw network.$interface.ifname=$device
361
362
				echo " -> $device attached to $interface"
			fi
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
	fi
}

qmp_get_ip6_slow() {
  local addr_prefix="$1"
  local addr="$(echo $addr_prefix | awk -F'/' '{print $1}')"
  local mask="$(echo $addr_prefix | awk -F'/' '{print $2}')"

  echo "qmp_get_ip6_slow addr_prefix=$addr_prefix addr=$addr mask=$mask" 1>&2

  if [ -z "$mask" ] ; then
    mask="128"
  fi

  local addr_in=$addr
  local addr_out=""
  local found=0

  while ! [ -z "$addr_in" ] ; do

    addr_in=$( echo $addr_in | sed -e "s/^://g" )

    if echo "$addr_in" | grep "^:"  >/dev/null 2>&1 ; then

      if echo "$addr_in" | grep "::"  >/dev/null 2>&1 ; then
        echo "Invalid 1 IPv6 address $addr_prefix" 1>&2
        return 1
      fi

      addr_in=$( echo $addr_in | sed -e "s/^://g" )

      if [ -z "$addr_in" ] ; then
        addr_out="$addr_out::"
      else
        addr_out="$addr_out:"
      fi

    else

      local addr16="$(echo $addr_in | awk -F':' '{print $1}')"
      addr_in=$( echo $addr_in | sed -e "s/^$addr16//g" )

      if [ -z "$addr_out" ] ; then
	addr_out="$addr16"
      else
	addr_out="$addr_out:$addr16"
      fi

      if echo "$addr16" | grep '\.'  >/dev/null 2>&1 ; then
        found=$(( $found + 2 ))
      else
        found=$(( $found + 1 ))
      fi

    fi

  done

  if echo $addr_out | grep "::" >/dev/null 2>&1 && [ "$found" -lt "8" ] ; then

    local insert="0"
    for n in $( seq $found "6" ) ; do
      insert="$insert:0"
    done

    addr_out=$( echo $addr_out | sed -e "s/^::$/$insert/g" )
    addr_out=$( echo $addr_out | sed -e "s/^::/$insert:/g" )
    addr_out=$( echo $addr_out | sed -e "s/::$/:$insert/g" )
    addr_out=$( echo $addr_out | sed -e "s/::/:$insert:/g" )

  elif echo $addr_out | grep "::"  >/dev/null 2>&1 || [ "$found" != "8" ] ; then
    echo "Invalid 2 IPv6 address $addr_prefix found=$found" 1>&2
    return 1
  fi


#  echo "Correct IPv6 address $addr_prefix addr_out=$addr_out found=$found" 1>&2
  local pos=0
  addr_in=$addr_out
  addr_out=""

  while ! [ -z "$addr_in" ] ; do

    addr_in=$( echo $addr_in | sed -e "s/^://g" )

    local addr16="$( echo $addr_in | awk -F':' '{print $1}' )"
    addr_in=$( echo $addr_in | sed -e "s/^$addr16//g" )

    if echo $addr16 | grep '\.' >/dev/null 2>&1  ; then
      local ip1=$( echo $addr16 | awk -F'.' '{print $1}' )
      local ip2=$( echo $addr16 | awk -F'.' '{print $2}' )
      local ip3=$( echo $addr16 | awk -F'.' '{print $3}' )
      local ip4=$( echo $addr16 | awk -F'.' '{print $4}' )

#      echo "addr16=$addr16 ip1=$ip1 ip2=$ip2 ip3=$ip3 ip4=$ip4" 1>&2

      addr16=$( printf "%X" $(( $(( $ip1 * 0x100 )) + $ip2 )) )

      if [ -z "$ip4" ] ; then
        echo "Invalid 3 IPv6 address $addr_prefix" 1>&2
        return 1
      fi

      addr_in=$( printf "%X" $(( $(( $ip3 * 0x100 )) + $ip4 )) )$addr_in


    fi

    local prefix16
    if [ "$pos" -le "$mask" ] ; then

      if [ "$(( $pos + 16 ))" -le "$mask" ] ; then
	prefix16=$addr16
      else
	prefix16=$( printf "%X" $(( 0x$addr16 & 0xFFFF<<$(( $(( $pos + 16 )) - $mask )) )) )
      fi

    else
      prefix16="0"
    fi


    if [ -z "$addr_out" ] ; then
      addr_out="$prefix16"
    else
      addr_out="$addr_out:$prefix16"
    fi

    pos=$(( $pos + 16 ))

  done

  echo "$addr_out"
}

qmp_get_ip6_fast() {

  if ! [ -x /usr/bin/ipv6calc ] ; then
     qmp_get_ip6_slow $1
     return $?
  fi

  local addr_prefix="$1"
  local addr="$(echo $addr_prefix | awk -F'/' '{print $1}')"
  local mask="$(echo $addr_prefix | awk -F'/' '{print $2}')"

  if [ -z "$mask" ] ; then
    echo "qmp_get_ip6_fast: ERROR addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2
    return 1
    mask="128"
  fi

515
  local addr_long=$( ipv6calc -q  --in ipv6 $addr --showinfo -m 2>&1 | awk -F'=' '/IPV6=/{print $2}' )
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621

  local fake_prefix16="20a2" # original input is manipulated because ipv6calc complains about reserved ipv6 addresses
  local addr_prefix16="$(echo $addr_long | awk -F':' '{print $1}')"
  local fake_long=$( echo $addr_long | sed -e "s/^$addr_prefix16/$fake_prefix16/g" )
  local fake_out

#  echo "qmp_get_ip6_fast: begin addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2

  if [ "$mask" -ge "0" ] &&  [ "$mask" -le "112" ] && [ "$(( $mask % 16))" = "0" ]; then

    fake_out="$( ipv6calc --in ipv6 $fake_long/$mask -F --printprefix --out ipv6addr 2>/dev/null )::/$mask"

  else

    if [ "$(( $mask % 16))" != "0" ]; then
      echo "ERROR addr_prefix=$1 mask=$mask must be multiple of 16" 1>&2
      return 1
    fi

    fake_out="$( ipv6calc --in ipv6 $fake_long/128 -F --printprefix --out ipv6addr 2>/dev/null )"
  fi

  echo $fake_out | sed -e "s/^$fake_prefix16/$addr_prefix16/g"

#  echo "qmp_get_ip6_fast: return addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2
}

qmp_calculate_ula96() {

  local prefix=$1
  local mac=$2
  local suffix=$3

  local prefix48=$( qmp_get_ip6_fast $prefix/128 )
  local suffix48=$( qmp_get_ip6_fast $suffix/128 )

# echo "qmp_calculate_ula96 suffix48=$suffix48" 1>&2

  local mac1="$( echo $mac | awk -F':' '{print $1}' )"
  local mac2="$( echo $mac | awk -F':' '{print $2}' )"
  local mac3="$( echo $mac | awk -F':' '{print $3}' )"
  local mac4="$( echo $mac | awk -F':' '{print $4}' )"
  local mac5="$( echo $mac | awk -F':' '{print $5}' )"
  local mac6="$( echo $mac | awk -F':' '{print $6}' )"

  local p1="$( echo $prefix48 | awk -F':' '{print $1}' )"
  local p2="$( echo $prefix48 | awk -F':' '{print $2}' )"
  local p3="$( echo $prefix48 | awk -F':' '{print $3}' )"

  local s1="$( echo $suffix48 | awk -F':' '{print $7}' )"
  local s2="$( echo $suffix48 | awk -F':' '{print $8}' )"

  printf "%X:%X:%X:%X:%X:%X:%X:%X\n" 0x$p1 0x$p2 0x$p3  $(( ( 0x$mac1 * 0x100 ) + 0x$mac2 ))  $(( ( 0x$mac3 * 0x100 ) + 0x$mac4 ))  $(( ( 0x$mac5 * 0x100 ) + 0x$mac6 ))  0x$s1 0x$s2

}

qmp_calculate_addr64() {

  local prefix=$1
  local node=$2
  local suffix=$3

  local prefix48=$( qmp_get_ip6_fast $prefix/128 )
  local suffix48=$( qmp_get_ip6_fast $suffix/128 )

  local p1="$( echo $prefix48 | awk -F':' '{print $1}' )"
  local p2="$( echo $prefix48 | awk -F':' '{print $2}' )"
  local p3="$( echo $prefix48 | awk -F':' '{print $3}' )"

  local s5="$( echo $suffix48 | awk -F':' '{print $5}' )"
  local s6="$( echo $suffix48 | awk -F':' '{print $6}' )"
  local s7="$( echo $suffix48 | awk -F':' '{print $7}' )"
  local s8="$( echo $suffix48 | awk -F':' '{print $8}' )"

  printf "%X:%X:%X:%X:%X:%X:%X:%X\n" 0x$p1 0x$p2 0x$p3   0x$node   0x$s5 0x$s6 0x$s7 0x$s8

}

qmp_get_ula96() {

  local prefix=$1
  local dev_mac=$2
  local suffix=$3
  local mask=$4

  local mac=$( qmp_get_mac_for_dev $dev_mac )
  local ula96=$( qmp_calculate_ula96 $prefix $mac $suffix )

  if [ -z "$mask" ] ; then
      echo "$ula96"
  else
      echo "$ula96/$mask"
  fi
}

qmp_get_addr64() {
  local prefix=$1
  local node=$2
  local suffix=$3
  local mask=$4
  local addr64=$( qmp_calculate_addr64 $prefix $node $suffix )
  echo "$addr64/$mask"
}

qmp_configure_prepare() {
  local conf=$1
p4u's avatar
p4u committed
622
   if ! [ -f /etc/config/$conf.orig ]; then
623
624
625
626
627
628
629
630
631
632
633
634
    echo "saving original config in: /etc/config/$conf.orig"
    cp /etc/config/$conf /etc/config/$conf.orig
  fi

  uci revert $conf
  echo "" > /etc/config/$conf
}

qmp_configure_network() {

  local conf="network"

p4u's avatar
p4u committed
635
636
637
638
  echo "-----------------------"
  echo "Configuring networking"
  echo "-----------------------"

639
  qmp_configure_prepare_network $conf
640

641
  # LoopBack device
642
643
644
645
646
647
648
  uci set $conf.loopback="interface"
  uci set $conf.loopback.ifname="lo"
  uci set $conf.loopback.proto="static"
  uci set $conf.loopback.ipaddr="127.0.0.1"
  uci set $conf.loopback.netmask="255.0.0.0"

  # WAN devices
649
650
  qmp_configure_wan
  # LAN devices
651
  qmp_configure_lan
652
653
  # MESH devices
  qmp_configure_mesh
654

655
656
657
658
  uci commit
}


659
qmp_remove_qmp_bmx6_tunnels()
660
{
661
	if echo "$1" | grep -q "^qmp_"
662
663
664
	then
		uci delete bmx6.$1
	fi
665
	uci commit bmx6
666
667
668
669
670
671
}

qmp_unconfigure_bmx6_gateways()
{
	config_load bmx6
	config_foreach qmp_remove_qmp_bmx6_tunnels tunInNet
672
673
	config_foreach qmp_remove_qmp_bmx6_tunnels tunDev
	config_foreach qmp_remove_qmp_bmx6_tunnels tunIn
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
	config_foreach qmp_remove_qmp_bmx6_tunnels tunOut
}

qmp_translate_configuration()
{
	orig_config=$1
	orig_section=$2
	orig_option=$3

	dest_config=$4
	dest_section=$5
	dest_option=${6:-$orig_option}

	value="$(uci -q get $orig_config.$orig_section.$orig_option)"
	if [ -n "$value" ]
	then
		uci set $dest_config.$dest_section.$dest_option="$value"
	fi
}

qmp_add_qmp_bmx6_tunnels()
{
	local section=$1
697
	local name="$section"
698
699
	local config=bmx6
	local ignore
700
	local t
701
	config_get ignore "$section" ignore
702

703
	[ "$ignore" = "1" ] && return
704

705
706
	local type="$(qmp_uci_get_raw gateways.$name.type)"
	qmp_log Configuring gateway $name of type $type
707
	[ -z "$name" ] && name="qmp_$gateway" || name="qmp_$name"
708
709

	if [ "$type" == "offer" ]
710
	then
711
		bmx6_type=tunIn
712
		uci set $config.$name="$bmx6_type"
713
		uci set $config.$name.$bmx6_type="$name"
714
715
716
		for t in \
			network \
			bandwidth
717
		do
718
719
			qmp_translate_configuration gateways $section $t $config $name
		done
720
721
722
	else
		bmx6_type=tunOut
		uci set $config.$name="$bmx6_type"
723
		uci set $config.$name.$bmx6_type="$section"
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
		for t in \
			network \
			srcNet \
			gwName \
			minPrefixLen \
			maxPrefixLen \
			hysteresis \
			rating \
			minBandwidth \
			tableRule \
			kernel \
			boot \
			static \
			zebra \
			system \
			connect \
			rip \
			ripng \
			ospf \
			ospf6 \
			isis \
			bgp \
			babel \
			olsr \
			exportDistance \
			srcType \
			gwId \
			ipMetric
752
		do
753
			qmp_translate_configuration gateways $section $t $config $name
754
		done
755
	fi
756

757
758
759
760
761
762
	gateway="$(($gateway + 1))"
}

qmp_configure_bmx6_gateways()
{
	qmp_unconfigure_bmx6_gateways
763
	config_load gateways
764
765
	gateway=0
	config_foreach qmp_add_qmp_bmx6_tunnels gateway
766
	uci commit bmx6
767
768
}

769
770
771
772
773
774
775
776
777
778
779
780
781
782
783

qmp_configure_bmx6() {
  local conf="bmx6"

  qmp_configure_prepare $conf
  uci set $conf.general="bmx6"
  uci set $conf.bmx6_config_plugin=plugin
  uci set $conf.bmx6_config_plugin.plugin=bmx6_config.so

  uci set $conf.bmx6_json_plugin=plugin
  uci set $conf.bmx6_json_plugin.plugin=bmx6_json.so

  uci set $conf.bmx6_sms_plugin=plugin
  uci set $conf.bmx6_sms_plugin.plugin=bmx6_sms.so

784
if [ -f /lib/bmx6_topology.so ]; then
785
786
  uci set $conf.bmx6_topology_plugin=plugin
  uci set $conf.bmx6_topology_plugin.plugin=bmx6_topology.so
787
fi
788

789
790
791
792
793
794
795
796
797
  # chat file must be syncronized using sms
  cfg_sms=$(uci add $conf syncSms)
  uci set $conf.${cfg_sms}.syncSms=chat

  uci set $conf.ipVersion=ipVersion
  uci set $conf.ipVersion.ipVersion="6"

  local primary_mesh_device="$(qmp_get_primary_device)"

798
799
  local device_id=$(qmp_get_id)
	device_id="$(echo -n $device_id | tr -cd 'ABCDEFabcdef0123456789' | tail -c 4)"
800
  if qmp_uci_test qmp.interfaces.mesh_devices &&
801
  qmp_uci_test qmp.networks.mesh_protocol_vids
802

803
    then
804
805
    local counter=1

806
807
  for dev in $(qmp_get_devices mesh); do
    echo "Configuring interface $dev in BMX6"
808

809
810
    for protocol_vid in $(uci get qmp.networks.mesh_protocol_vids); do
      local protocol_name="$(echo $protocol_vid | awk -F':' '{print $1}')"
811

812
813
814
815
816
817
      if [ "$protocol_name" = "bmx6" ] ; then
        # Check if the current device is configured as no-vlan
        local use_vlan=1
        for no_vlan_int in $(qmp_uci_get interfaces.no_vlan_devices); do
          [ "$no_vlan_int" == "$dev" ] && use_vlan=0
        done
818

819
820
821
        # Check if the protocol has VLAN tag configured
        local vid="$(echo $protocol_vid | awk -F':' '{print $2}')"
        [ -z "$vid" -o $vid -lt 1 ] && use_vlan=0
822

823
824
825
        # Check if the protocol has VLAN tag configured
        local vid="$(echo $protocol_vid | awk -F':' '{print $2}')"
        [ -z "$vid" -o $vid -lt 1 ] && use_vlan=0
826

827
828
829
830
831
        # If vlan tagging
        if [ $use_vlan -eq 1 ]; then
          # For interfaces like eth0.1, replace the dot with an underscore
          local viface="$(echo $dev | sed -r 's/\./_/g')"
          local ifname="${viface}_${vid}"
832

833
	# If not vlan tagging
834
835
836
		else
			local ifname="$dev"
		fi
837

838
839
840
841
842
		# If the interface is in the LAN bridge (br-lan) and does not use VLANed mesh, add the bridge instead
		if [ $(qmp_get_virtual_iface $dev) == "lan" ] && [ $use_vlan == "0" ]; then
			ifname="br-lan"
		fi

843
844
		uci set $conf.mesh_$counter="dev"
		uci set $conf.mesh_$counter.dev="$ifname"
845
		if [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ]; then
846
			uci set $conf.mesh_$counter.linklayer=1
847
848
		else
			uci set $conf.mesh_$counter.linklayer=2
849
		fi
850
851
852
853
854
855

	    if qmp_uci_test qmp.networks.bmx6_ipv4_address ; then
	      local bmx6_ipv4_netmask="$(echo $(uci get qmp.networks.bmx6_ipv4_address) | cut -s -d / -f2)"
	      local bmx6_ipv4_address="$(echo $(uci get qmp.networks.bmx6_ipv4_address) | cut -d / -f1)"
	      [ -z "$bmx6_ipv4_netmask" ] && bmx6_ipv4_netmask="32"
	      uci set $conf.general.tun4Address="$bmx6_ipv4_address/$bmx6_ipv4_netmask"
856
857
858
	      uci set $conf.tmain=tunDev
	      uci set $conf.tmain.tunDev=tmain
	      uci set $conf.tmain.tun4Address="$bmx6_ipv4_address/$bmx6_ipv4_netmask"
859

860
	    else
p4u's avatar
p4u committed
861
	      local ipv4_suffix24="$(qmp_get_id 8bit)"
862
	      local ipv4_prefix24="$(qmp_uci_get networks.bmx6_ipv4_prefix24)"
863
864
865
866
	      if [ $(echo -n "$ipv4_prefix24" | tr -d [0-9] | wc -c) -lt 2 ]; then
	      	ipv4_prefix24="${ipv4_prefix24}.0"
	      fi
	      uci set $conf.general.tun4Address="$ipv4_prefix24.$ipv4_suffix24/32"
867
868
869
	      uci set $conf.tmain=tunDev
	      uci set $conf.tmain.tunDev=tmain
	      uci set $conf.tmain.tun4Address="$ipv4_prefix24.$ipv4_suffix24/32"
870

871
872
873
874
875
876
877
878
879
880
	    fi
	    counter=$(( $counter + 1 ))
         fi

       done
    done
  fi


  if qmp_uci_test qmp.networks.bmx6_ripe_prefix48 ; then
881
    uci set $conf.general.tun6Address="$(uci get qmp.networks.bmx6_ripe_prefix48):$device_id:0:0:0:1/64"
882
883
    uci set $conf.tmain=tunDev
    uci set $conf.tmain.tunDev=tmain
884
    uci set $conf.tmain.tun6Address="$(qmp_uci_get networks.bmx6_ripe_prefix48):$device_id:0:0:0:1/64"
885
886
  fi

887
  qmp_configure_bmx6_gateways
888
889
890
891
892

  uci commit $conf
#  /etc/init.d/$conf restart
}

p4u's avatar
p4u committed
893
qmp_restart_firewall() {
894
895
896
	iptables -F
	iptables -F -t nat
	sh /etc/firewall.user
p4u's avatar
p4u committed
897
}
898
899

qmp_check_force_internet() {
900
901
	[ "$(qmp_uci_get networks.force_internet)" == "1" ] && qmp_gw_offer_default
	[ "$(qmp_uci_get networks.force_internet)" == "0" ] && qmp_gw_search_default
902
903
}

904
qmp_configure_initial() {
905
	qmp_hooks_exec firstboot
906
907
	qmp_configure_wifi_initial
	qmp_configure_wifi
908
	/etc/init.d/network reload
909
910
	/etc/init.d/network restart
	sleep 5 # Let WiFi devices start up
911
912
913
	qmp_configure_smart_network
}

914
qmp_configure() {
915
  qmp_configure_system
916
  qmp_set_services
917
  qmp_hooks_exec preconf
918
919
920
921
  qmp_check_force_internet
  qmp_configure_network
  qmp_configure_bmx6
  qmp_configure_lan_v6
922
  qmp_hooks_exec postconf
923
}