Developing lightweight computation at the DSG edge

qmp_functions.sh 24.3 KB
Newer Older
1
#!/bin/sh
2
# requires ip ipv6calc awk sed grep
3
4
5
6
7
8
QMP_PATH="/etc/qmp"
SOURCE_FUNCTIONS=1

#######################
# Importing files
######################
9
10
11
12
13
if [ -z "$SOURCE_OPENWRT_FUNCTIONS" ]
then
	. /lib/functions.sh
	SOURCE_OPENWRT_FUNCTIONS=1
fi
14
15
16
. $QMP_PATH/qmp_common.sh
[ -z "$SOURCE_GW" ] && . $QMP_PATH/qmp_gw.sh
[ -z "$SOURCE_NET" ] && . $QMP_PATH/qmp_network.sh
17
[ -z "$SOURCE_SYS" ] && . $QMP_PATH/qmp_system.sh
18
[ -z "$SOURCE_WIRELESS" ] && . $QMP_PATH/qmp_wireless.sh
19
[ -z "$SOURCE_COMMON" ] && . $QMP_PATH/qmp_common.sh
20
21
22

qmp_get_llocal_for_dev() {
  local dev=$1
23
  ip a show dev $dev | awk '/inet6/{print $2}'
24
25
26
27
28
}

# returns primary device
qmp_get_primary_device() {
  local primary_mesh_device="$(uci get qmp.node.primary_device)"
29
  [ -z "$primary_mesh_device" ] &&
30
31
32
33
34
35
      {
      if ip link show dev eth0 > /dev/null; then
        primary_mesh_device="eth0"
      else
        primary_mesh_device="$(ip link show | awk '!/lo:/&&/^[0-9]?:/{sub(/:$/,"",$2); print $2; exit}')"
      fi
36
      [ -z "$primary_mesh_device" ] && echo "CRITICAL: No primary network device found, please define qmp.node.primary_device"
37
38
39
40
      }
  echo "$primary_mesh_device"
}

41
# check if a device exists
42
43
44
45
qmp_check_device() {
	ip link show $1 1> /dev/null 2>/dev/null
	return $?
}
46
47
48
49
50
51
52
# Function qmp_set_vlan()
#
# This function creates a VLAN interface on top of an interface in order to
# isolate the routing protocol traffic there:
#
#  - 802.1 VLANs are used for wireless interfaces.
#  - 802.1ad (QinQ) VLANs are used for wired devices since qMp > 3.2.1
53
qmp_set_vlan() {
54
55
56
  local iface="$1" # The physical interface
  local vid=$2     # The VLAN
  local liface=$3  # The logical interface lan/wan_X/mesh_Y
57

58
59
  echo "Setting VLAN $vid for interface $iface"
  [ -z "$iface" ] || [ -z "$vid" ] && return
60

61
62
  # Replace dots by underscores to use the interface name as part of another one
  local uiface="$(echo $iface | sed -r 's/\./_/g')" 
63

64
  uci set network.${uiface}_${vid}=device
65
  if [ -e "/sys/class/net/$dev/phy80211" ]; then
66
    # 802.1q VLANs for wireless interfaces
67
    uci set network.${uiface}_${vid}.type=8021q
68
  else
69
    # 802.1ad VLANs for wired interfaces
70
    uci set network.${uiface}_${vid}.type=8021ad
71
  fi
72

73
  uci set network.${uiface}_${vid}.name=${uiface}_${vid}
74
  if [ -e "/sys/class/net/$dev/phy80211" ]; then
75
76
77
    # VLANs for wireless interfaces need to be configured on top of the
    # logical interface the radio is put in (e.g. mesh_w0 for wlan0)
    uci set network.${uiface}_${vid}.ifname='@'${liface}
78
  else
79
80
81
    # VLANs for wired interfaces are configured directly on top of the physical
    # interface (e.g. eth0.2, eth1)
    uci set network.${uiface}_${vid}.ifname=${iface}
82
  fi
83
  uci set network.${uiface}_${vid}.vid=${vid}
84

85
86
87
88
  uci set network.${uiface}_${vid}_ad=interface
  uci set network.${uiface}_${vid}_ad.ifname=${uiface}_${vid}
  uci set network.${uiface}_${vid}_ad.proto=${none}
  uci set network.${uiface}_${vid}_ad.auto=1
89
  uci commit network
90

91
92
93
94
95
96
}

qmp_get_virtual_iface() {
  local device="$1"
  local viface=""

97
98
99
100
101
102
103
104
105
  if qmp_is_routerstationpro; then
    if [ "$device" == "eth1" ]; then
      echo "rsp_e1"
      return
    fi
    if [ "$device" == "eth1.1" ]; then
      echo "rsp_e1_1"
      return
    fi
106
107
  fi

108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
	# is lan?
	if [ "$device" == "br-lan" ]; then
		viface="lan"
		if [ ! -e "/sys/class/net/$device/phy80211" ]; then
			echo $viface
			return
		fi
  	fi

	for l in $(qmp_get_devices lan); do
		if [ "$l" == "$device" ]; then
			viface="lan"
			if [ ! -e "/sys/class/net/$device/phy80211" ]; then
				echo $viface
				return
			fi
		fi
	done
126

127
	[ ! -e "/sys/class/net/$device/phy80211" ] && [ -n "$viface" ] && { echo $viface; return; }
128

129
130
131
	# id is the first char and the numbers of the device [e]th[0] [w]lan[1]
	local id_num=$(echo $device | tr -d "[A-z]" | tr - _ | tr . _)
	local id_char=$(echo $device | cut -c 1)
132

133
134
135
136
137
138
139
140
	# is wan?
	for w in $(qmp_get_devices wan); do
		if [ "$w" == "$device" ]; then
			viface="wan_${id_char}${id_num}"
			echo $viface
			return
		fi
	done
141

142
143
	qmp_log "LOG: 5"
		qmp_log "Viface: $viface"
144

145
146
147
148
149
150
151
	# is mesh?
	for w in $(qmp_get_devices mesh); do
		if [ "$w" == "$device" ]; then
			viface="mesh_${id_char}${id_num}"
			break
		fi
	done
152

153
	echo "$viface"
154
155
156
157
158
159
}

# arg1=<mesh|lan|wan>, returns the devices which have to be configured in such mode
qmp_get_devices() {
  local devices=""

160
  if [ "$1" == "mesh" ]; then
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
		devices="$(uci get qmp.interfaces.mesh_devices 2>/dev/null)"
	fi
  #   local brlan_enabled=0
  #   for dev in $(uci get qmp.interfaces.mesh_devices 2>/dev/null); do
	# 
  #       # Looking if device is defined as LAN, in such case dev=br-lan, but only once
  #       # except eth1 for RouterStation Pro
  #       if ! ( [[ "$dev" == "eth1" ]] && qmp_is_routerstationpro ) ; then
  #           for landev in $(uci get qmp.interfaces.lan_devices 2>/dev/null); do
  #               if [ "$landev" == "$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ] ; then
  #                   if [ $brlan_enabled -eq 0 ]; then
  #                       dev="br-lan"
  #                       brlan_enabled=1
  #                   else
  #                       dev=""
  #                   fi
  #                   break
  #               fi
  #           done
  #       fi
	# 
  #     [ -n "$dev" ] && devices="$devices $dev"
  #   done
  # fi
185
186
187
188
189
190
191
192
193

  if [ "$1" == "lan" ]; then
     devices="$(uci get qmp.interfaces.lan_devices 2>/dev/null)"
  fi

  if [ "$1" == "wan" ]; then
     devices="$(uci get qmp.interfaces.wan_devices 2>/dev/null)"
  fi

194
195
196
197
  if qmp_is_routerstationpro && [ "$1" == "wan" -o "$1" == "lan" ]; then
     devices="$(echo $devices | sed -e "s/\beth1\b/eth1.1/g")"
  fi

198
199
200
201
  echo "$devices"
}


202
# Scan and configure the network devices (lan, mesh and wan)
203
# if $1 is set to "force", it rescan all devices
204
205
206
207
qmp_configure_smart_network() {
	echo "---------------------------------------"
	echo "Starting smart networking configuration"
	echo "---------------------------------------"
208
	local force=$1
209
210
211
212
213
	local mesh=""
	local wan=""
	local lan=""
	local dev=""
	local phydevs=""
214
	local ignore_devs=""
215

216
217
218
	[ "$force" != "force" ] && {
		ignore_devs="$(qmp_uci_get interfaces.ignore_devices)"
	}
219

220
	for dev in $(ls /sys/class/net/); do
221
		[ -e /sys/class/net/$dev/device ] || [ dev == "eth0" ] && {
222
			local id
223
			local ignore=0
224

225
			# Check if device is in the ignore list
226
227
228
229
				for id in $ignore_devs; do
					[ "$id" == "$dev" ] && ignore=1
				done

230
231
232
233
234
235
236
237
238
239
			# [Qin] The device might be a wired device (e.g. eth0) with a switch
			# and two or more virtual switched devices (e.g. eth0.1, eth0.2)
			for sdev in $(ls /sys/class/net/$dev/ | grep upper_$dev. | cut -d "_" -f2); do
				phydevs="$phydevs $sdev\n"
				ignore=1
			done

			if [ $ignore -eq 0 ]; then
				phydevs="$phydevs $dev\n"
			fi
240
		}
241
	done
242
	phydevs="$(echo -e "$phydevs" | grep -v -e ".*ap$" | sort -u | tr -d ' ' \t)"
243

244
245
246
247
248
249
	# if force is not enabled, we are not changing the existing lan/wan/mesh (only adding new ones)
	[ "$force" != "force" ] && {
		lan="$(qmp_uci_get interfaces.lan_devices)"
		wan="$(qmp_uci_get interfaces.wan_devices)"
		mesh="$(qmp_uci_get interfaces.mesh_devices)"
	}
250

251
252
	local j=0
	local mode=""
253
254
	local cnt
	local cdev
255

256
	for dev in $phydevs; do
257
		# If force is enabled, do not check if the device is already configured
258
		[ "$force" != "force" ] && {
259

260
261
			cnt=0
			# If it is already configured, doing nothing
262
			for cdev in $lan; do
263
				[ "$cdev" == "$dev" ] && cnt=1
264
			done
265
			for cdev in $mesh; do
266
				[ "$cdev" == "$dev" ] && cnt=1
267
			done
268
			for cdev in $wan; do
269
				[ "$cdev" == "$dev" ] && cnt=1
270
271
272
			done
			[ $cnt -eq 1 ] && continue
		}
273

274
		# If not found before...
275
276
277
		[ "$dev" == "eth0" ] || [ "$dev" == "eth0.1" ] && {
			lan="$lan $dev"
			mesh="$mesh $dev"
278
279
280
281
282
			continue
		}

		## if there is not yet a LAN device, configuring as lan and mesh
		##[ -z "$lan" ] && { lan="$dev"; mesh="$dev" && continue
283
284
285
286
287
288
289
290
291
292
293
294
295
296

		# if it is a wifi device
		[ -e "/sys/class/net/$dev/phy80211" ] && {
			j=0
			while qmp_uci_test qmp.@wireless[$j]; do
				[ "$(qmp_uci_get @wireless[$j].device)" == "$dev" ] && {
					mode="$(qmp_uci_get @wireless[$j].mode)"
					[ "$mode" == "ap" ] && lan="$dev $lan" || mesh="$dev $mesh"
					break
				}
				j=$(($j+1))
			done
		} && continue

297
298
		# if there is already LAN device and it is not wifi, use as WAN+MESH
		[ -z "$wan" ] && wan="$dev" && mesh="$mesh $dev" || {
299
300
301
302
			# else use as LAN and MESH
			lan="$dev $lan"
			mesh="$dev $mesh"
		}
303

304
	done
305

306
	echo "Network devices found:"
307
308
309
310
	echo "- LAN $lan"
	echo "- MESH $mesh"
	echo "- WAN $wan"

311
	# Writes the devices to the config
312
313
314
	qmp_uci_set interfaces.lan_devices "$(echo $lan | sed -e s/"^ "//g -e s/" $"//g)"
	qmp_uci_set interfaces.mesh_devices "$(echo $mesh | sed -e s/"^ "//g -e s/" $"//g)"
	qmp_uci_set interfaces.wan_devices "$(echo $wan | sed -e s/"^ "//g -e s/" $"//g)"
315
	qmp_uci_set interfaces.ignore_devices "$ignore_devs"
316
317
}

318
319
qmp_attach_device_to_interface() {
	local device=$1
320
	local interface=$2
321
322
	local intype="$(qmp_uci_get_raw network.$interface.type)"

323
	echo "Attaching device $device to interface $interface"
324
325

	# is it a wifi device?
326
	if qmp_uci_test wireless.$device; then
327
		qmp_uci_set_raw wireless.$device.network=$interface
328
		echo " -> $device wireless attached to $interface"
329
330

	# if it is not
331
	else
332
			if [ "$intype" == "bridge" ]; then
333
				qmp_uci_add_list_raw network.$interface.ifname=$device
334
335
				echo " -> $device attached to $interface bridge"
			else
336
				qmp_uci_set_raw network.$interface.ifname=$device
337
338
				echo " -> $device attached to $interface"
			fi
339
340
341
	fi
}

342
qmp_is_routerstationpro() {
343
	cat /proc/cpuinfo | grep -q "^machine[[:space:]]*: No Ubiquiti RouterStation Pro at all$"
344
345
346
347
348
349
350
351
352
353
354
355
}

qmp_configure_routerstationpro_switch() {
	local vids="$@"

	uci set network.eth1="switch"
	uci set network.eth1.enable="1"
	uci set network.eth1.enable_vlan="1"
	uci set network.eth1.reset="1"

	uci set network.mesh_ports_vid1="switch_vlan"
	uci set network.mesh_ports_vid1.vlan="1"
356
	uci set network.mesh_ports_vid1.vid="1"
357
358
	uci set network.mesh_ports_vid1.device="eth1"
	uci set network.mesh_ports_vid1.ports="0t 4"
359

360
361
362
363
364
365
366
367
	for vid in $vids
	do
		uci set network.mesh_ports_vid$vid="switch_vlan"
		uci set network.mesh_ports_vid$vid.vlan="$vid"
		uci set network.mesh_ports_vid$vid.vid="$vid"
		uci set network.mesh_ports_vid$vid.device="eth1"
		uci set network.mesh_ports_vid$vid.ports="0t 2t 3t"
	done
368
369
370
371
372
373

	local viface="$(qmp_get_virtual_iface eth1)"
	uci set network.$viface="interface"
	uci set network.$viface.proto="static"
	uci set network.$viface.ifname="eth1"
	uci commit network
374
375
}

376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
qmp_get_ip6_slow() {
  local addr_prefix="$1"
  local addr="$(echo $addr_prefix | awk -F'/' '{print $1}')"
  local mask="$(echo $addr_prefix | awk -F'/' '{print $2}')"

  echo "qmp_get_ip6_slow addr_prefix=$addr_prefix addr=$addr mask=$mask" 1>&2

  if [ -z "$mask" ] ; then
    mask="128"
  fi

  local addr_in=$addr
  local addr_out=""
  local found=0

  while ! [ -z "$addr_in" ] ; do

    addr_in=$( echo $addr_in | sed -e "s/^://g" )

    if echo "$addr_in" | grep "^:"  >/dev/null 2>&1 ; then

      if echo "$addr_in" | grep "::"  >/dev/null 2>&1 ; then
        echo "Invalid 1 IPv6 address $addr_prefix" 1>&2
        return 1
      fi

      addr_in=$( echo $addr_in | sed -e "s/^://g" )

      if [ -z "$addr_in" ] ; then
        addr_out="$addr_out::"
      else
        addr_out="$addr_out:"
      fi

    else

      local addr16="$(echo $addr_in | awk -F':' '{print $1}')"
      addr_in=$( echo $addr_in | sed -e "s/^$addr16//g" )

      if [ -z "$addr_out" ] ; then
	addr_out="$addr16"
      else
	addr_out="$addr_out:$addr16"
      fi

      if echo "$addr16" | grep '\.'  >/dev/null 2>&1 ; then
        found=$(( $found + 2 ))
      else
        found=$(( $found + 1 ))
      fi

    fi

  done

  if echo $addr_out | grep "::" >/dev/null 2>&1 && [ "$found" -lt "8" ] ; then

    local insert="0"
    for n in $( seq $found "6" ) ; do
      insert="$insert:0"
    done

    addr_out=$( echo $addr_out | sed -e "s/^::$/$insert/g" )
    addr_out=$( echo $addr_out | sed -e "s/^::/$insert:/g" )
    addr_out=$( echo $addr_out | sed -e "s/::$/:$insert/g" )
    addr_out=$( echo $addr_out | sed -e "s/::/:$insert:/g" )

  elif echo $addr_out | grep "::"  >/dev/null 2>&1 || [ "$found" != "8" ] ; then
    echo "Invalid 2 IPv6 address $addr_prefix found=$found" 1>&2
    return 1
  fi


#  echo "Correct IPv6 address $addr_prefix addr_out=$addr_out found=$found" 1>&2
  local pos=0
  addr_in=$addr_out
  addr_out=""

  while ! [ -z "$addr_in" ] ; do

    addr_in=$( echo $addr_in | sed -e "s/^://g" )

    local addr16="$( echo $addr_in | awk -F':' '{print $1}' )"
    addr_in=$( echo $addr_in | sed -e "s/^$addr16//g" )

    if echo $addr16 | grep '\.' >/dev/null 2>&1  ; then
      local ip1=$( echo $addr16 | awk -F'.' '{print $1}' )
      local ip2=$( echo $addr16 | awk -F'.' '{print $2}' )
      local ip3=$( echo $addr16 | awk -F'.' '{print $3}' )
      local ip4=$( echo $addr16 | awk -F'.' '{print $4}' )

#      echo "addr16=$addr16 ip1=$ip1 ip2=$ip2 ip3=$ip3 ip4=$ip4" 1>&2

      addr16=$( printf "%X" $(( $(( $ip1 * 0x100 )) + $ip2 )) )

      if [ -z "$ip4" ] ; then
        echo "Invalid 3 IPv6 address $addr_prefix" 1>&2
        return 1
      fi

      addr_in=$( printf "%X" $(( $(( $ip3 * 0x100 )) + $ip4 )) )$addr_in


    fi

    local prefix16
    if [ "$pos" -le "$mask" ] ; then

      if [ "$(( $pos + 16 ))" -le "$mask" ] ; then
	prefix16=$addr16
      else
	prefix16=$( printf "%X" $(( 0x$addr16 & 0xFFFF<<$(( $(( $pos + 16 )) - $mask )) )) )
      fi

    else
      prefix16="0"
    fi


    if [ -z "$addr_out" ] ; then
      addr_out="$prefix16"
    else
      addr_out="$addr_out:$prefix16"
    fi

    pos=$(( $pos + 16 ))

  done

  echo "$addr_out"
}

qmp_get_ip6_fast() {

  if ! [ -x /usr/bin/ipv6calc ] ; then
     qmp_get_ip6_slow $1
     return $?
  fi

  local addr_prefix="$1"
  local addr="$(echo $addr_prefix | awk -F'/' '{print $1}')"
  local mask="$(echo $addr_prefix | awk -F'/' '{print $2}')"

  if [ -z "$mask" ] ; then
    echo "qmp_get_ip6_fast: ERROR addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2
    return 1
    mask="128"
  fi

525
  local addr_long=$( ipv6calc -q  --in ipv6 $addr --showinfo -m 2>&1 | awk -F'=' '/IPV6=/{print $2}' )
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631

  local fake_prefix16="20a2" # original input is manipulated because ipv6calc complains about reserved ipv6 addresses
  local addr_prefix16="$(echo $addr_long | awk -F':' '{print $1}')"
  local fake_long=$( echo $addr_long | sed -e "s/^$addr_prefix16/$fake_prefix16/g" )
  local fake_out

#  echo "qmp_get_ip6_fast: begin addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2

  if [ "$mask" -ge "0" ] &&  [ "$mask" -le "112" ] && [ "$(( $mask % 16))" = "0" ]; then

    fake_out="$( ipv6calc --in ipv6 $fake_long/$mask -F --printprefix --out ipv6addr 2>/dev/null )::/$mask"

  else

    if [ "$(( $mask % 16))" != "0" ]; then
      echo "ERROR addr_prefix=$1 mask=$mask must be multiple of 16" 1>&2
      return 1
    fi

    fake_out="$( ipv6calc --in ipv6 $fake_long/128 -F --printprefix --out ipv6addr 2>/dev/null )"
  fi

  echo $fake_out | sed -e "s/^$fake_prefix16/$addr_prefix16/g"

#  echo "qmp_get_ip6_fast: return addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2
}

qmp_calculate_ula96() {

  local prefix=$1
  local mac=$2
  local suffix=$3

  local prefix48=$( qmp_get_ip6_fast $prefix/128 )
  local suffix48=$( qmp_get_ip6_fast $suffix/128 )

# echo "qmp_calculate_ula96 suffix48=$suffix48" 1>&2

  local mac1="$( echo $mac | awk -F':' '{print $1}' )"
  local mac2="$( echo $mac | awk -F':' '{print $2}' )"
  local mac3="$( echo $mac | awk -F':' '{print $3}' )"
  local mac4="$( echo $mac | awk -F':' '{print $4}' )"
  local mac5="$( echo $mac | awk -F':' '{print $5}' )"
  local mac6="$( echo $mac | awk -F':' '{print $6}' )"

  local p1="$( echo $prefix48 | awk -F':' '{print $1}' )"
  local p2="$( echo $prefix48 | awk -F':' '{print $2}' )"
  local p3="$( echo $prefix48 | awk -F':' '{print $3}' )"

  local s1="$( echo $suffix48 | awk -F':' '{print $7}' )"
  local s2="$( echo $suffix48 | awk -F':' '{print $8}' )"

  printf "%X:%X:%X:%X:%X:%X:%X:%X\n" 0x$p1 0x$p2 0x$p3  $(( ( 0x$mac1 * 0x100 ) + 0x$mac2 ))  $(( ( 0x$mac3 * 0x100 ) + 0x$mac4 ))  $(( ( 0x$mac5 * 0x100 ) + 0x$mac6 ))  0x$s1 0x$s2

}

qmp_calculate_addr64() {

  local prefix=$1
  local node=$2
  local suffix=$3

  local prefix48=$( qmp_get_ip6_fast $prefix/128 )
  local suffix48=$( qmp_get_ip6_fast $suffix/128 )

  local p1="$( echo $prefix48 | awk -F':' '{print $1}' )"
  local p2="$( echo $prefix48 | awk -F':' '{print $2}' )"
  local p3="$( echo $prefix48 | awk -F':' '{print $3}' )"

  local s5="$( echo $suffix48 | awk -F':' '{print $5}' )"
  local s6="$( echo $suffix48 | awk -F':' '{print $6}' )"
  local s7="$( echo $suffix48 | awk -F':' '{print $7}' )"
  local s8="$( echo $suffix48 | awk -F':' '{print $8}' )"

  printf "%X:%X:%X:%X:%X:%X:%X:%X\n" 0x$p1 0x$p2 0x$p3   0x$node   0x$s5 0x$s6 0x$s7 0x$s8

}

qmp_get_ula96() {

  local prefix=$1
  local dev_mac=$2
  local suffix=$3
  local mask=$4

  local mac=$( qmp_get_mac_for_dev $dev_mac )
  local ula96=$( qmp_calculate_ula96 $prefix $mac $suffix )

  if [ -z "$mask" ] ; then
      echo "$ula96"
  else
      echo "$ula96/$mask"
  fi
}

qmp_get_addr64() {
  local prefix=$1
  local node=$2
  local suffix=$3
  local mask=$4
  local addr64=$( qmp_calculate_addr64 $prefix $node $suffix )
  echo "$addr64/$mask"
}

qmp_configure_prepare() {
  local conf=$1
p4u's avatar
p4u committed
632
   if ! [ -f /etc/config/$conf.orig ]; then
633
634
635
636
637
638
639
640
641
642
643
644
    echo "saving original config in: /etc/config/$conf.orig"
    cp /etc/config/$conf /etc/config/$conf.orig
  fi

  uci revert $conf
  echo "" > /etc/config/$conf
}

qmp_configure_network() {

  local conf="network"

p4u's avatar
p4u committed
645
646
647
648
  echo "-----------------------"
  echo "Configuring networking"
  echo "-----------------------"

649
  qmp_configure_prepare_network $conf
650

651
  # LoopBack device
652
653
654
655
656
657
658
  uci set $conf.loopback="interface"
  uci set $conf.loopback.ifname="lo"
  uci set $conf.loopback.proto="static"
  uci set $conf.loopback.ipaddr="127.0.0.1"
  uci set $conf.loopback.netmask="255.0.0.0"

  # WAN devices
659
660
  qmp_configure_wan
  # LAN devices
661
  qmp_configure_lan
662
663
  # MESH devices
  qmp_configure_mesh
664

665
666
667
668
  uci commit
}


669
qmp_remove_qmp_bmx6_tunnels()
670
{
671
	if echo "$1" | grep -q "^qmp_"
672
673
674
	then
		uci delete bmx6.$1
	fi
675
	uci commit bmx6
676
677
678
679
680
681
}

qmp_unconfigure_bmx6_gateways()
{
	config_load bmx6
	config_foreach qmp_remove_qmp_bmx6_tunnels tunInNet
682
683
	config_foreach qmp_remove_qmp_bmx6_tunnels tunDev
	config_foreach qmp_remove_qmp_bmx6_tunnels tunIn
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
	config_foreach qmp_remove_qmp_bmx6_tunnels tunOut
}

qmp_translate_configuration()
{
	orig_config=$1
	orig_section=$2
	orig_option=$3

	dest_config=$4
	dest_section=$5
	dest_option=${6:-$orig_option}

	value="$(uci -q get $orig_config.$orig_section.$orig_option)"
	if [ -n "$value" ]
	then
		uci set $dest_config.$dest_section.$dest_option="$value"
	fi
}

qmp_add_qmp_bmx6_tunnels()
{
	local section=$1
707
	local name="$section"
708
709
	local config=bmx6
	local ignore
710
	local t
711
	config_get ignore "$section" ignore
712

713
	[ "$ignore" = "1" ] && return
714

715
716
	local type="$(qmp_uci_get_raw gateways.$name.type)"
	qmp_log Configuring gateway $name of type $type
717
	[ -z "$name" ] && name="qmp_$gateway" || name="qmp_$name"
718
719

	if [ "$type" == "offer" ]
720
	then
721
		bmx6_type=tunIn
722
		uci set $config.$name="$bmx6_type"
723
		uci set $config.$name.$bmx6_type="$name"
724
725
726
		for t in \
			network \
			bandwidth
727
		do
728
729
			qmp_translate_configuration gateways $section $t $config $name
		done
730
731
732
	else
		bmx6_type=tunOut
		uci set $config.$name="$bmx6_type"
733
		uci set $config.$name.$bmx6_type="$section"
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
		for t in \
			network \
			srcNet \
			gwName \
			minPrefixLen \
			maxPrefixLen \
			hysteresis \
			rating \
			minBandwidth \
			tableRule \
			kernel \
			boot \
			static \
			zebra \
			system \
			connect \
			rip \
			ripng \
			ospf \
			ospf6 \
			isis \
			bgp \
			babel \
			olsr \
			exportDistance \
			srcType \
			gwId \
			ipMetric
762
		do
763
			qmp_translate_configuration gateways $section $t $config $name
764
		done
765
	fi
766

767
768
769
770
771
772
	gateway="$(($gateway + 1))"
}

qmp_configure_bmx6_gateways()
{
	qmp_unconfigure_bmx6_gateways
773
	config_load gateways
774
775
	gateway=0
	config_foreach qmp_add_qmp_bmx6_tunnels gateway
776
	uci commit bmx6
777
778
}

779
780
781
782
783
784
785
786
787
788
789
790
791
792
793

qmp_configure_bmx6() {
  local conf="bmx6"

  qmp_configure_prepare $conf
  uci set $conf.general="bmx6"
  uci set $conf.bmx6_config_plugin=plugin
  uci set $conf.bmx6_config_plugin.plugin=bmx6_config.so

  uci set $conf.bmx6_json_plugin=plugin
  uci set $conf.bmx6_json_plugin.plugin=bmx6_json.so

  uci set $conf.bmx6_sms_plugin=plugin
  uci set $conf.bmx6_sms_plugin.plugin=bmx6_sms.so

794
if [ -f /lib/bmx6_topology.so ]; then
795
796
  uci set $conf.bmx6_topology_plugin=plugin
  uci set $conf.bmx6_topology_plugin.plugin=bmx6_topology.so
797
fi
798

799
800
801
802
803
804
805
806
807
  # chat file must be syncronized using sms
  cfg_sms=$(uci add $conf syncSms)
  uci set $conf.${cfg_sms}.syncSms=chat

  uci set $conf.ipVersion=ipVersion
  uci set $conf.ipVersion.ipVersion="6"

  local primary_mesh_device="$(qmp_get_primary_device)"

808
809
  local device_id=$(qmp_get_id)
	device_id="$(echo -n $device_id | tr -cd 'ABCDEFabcdef0123456789' | tail -c 4)"
810
  if qmp_uci_test qmp.interfaces.mesh_devices &&
811
  qmp_uci_test qmp.networks.mesh_protocol_vids
812

813
    then
814
815
    local counter=1

816
817
  for dev in $(qmp_get_devices mesh); do
    echo "Configuring interface $dev in BMX6"
818

819
820
    for protocol_vid in $(uci get qmp.networks.mesh_protocol_vids); do
      local protocol_name="$(echo $protocol_vid | awk -F':' '{print $1}')"
821

822
823
824
825
826
827
      if [ "$protocol_name" = "bmx6" ] ; then
        # Check if the current device is configured as no-vlan
        local use_vlan=1
        for no_vlan_int in $(qmp_uci_get interfaces.no_vlan_devices); do
          [ "$no_vlan_int" == "$dev" ] && use_vlan=0
        done
828

829
830
831
        # Check if the protocol has VLAN tag configured
        local vid="$(echo $protocol_vid | awk -F':' '{print $2}')"
        [ -z "$vid" -o $vid -lt 1 ] && use_vlan=0
832

833
834
835
        # Check if the protocol has VLAN tag configured
        local vid="$(echo $protocol_vid | awk -F':' '{print $2}')"
        [ -z "$vid" -o $vid -lt 1 ] && use_vlan=0
836

837
838
839
840
841
        # If vlan tagging
        if [ $use_vlan -eq 1 ]; then
          # For interfaces like eth0.1, replace the dot with an underscore
          local viface="$(echo $dev | sed -r 's/\./_/g')"
          local ifname="${viface}_${vid}"
842

843
	# If not vlan tagging
844
845
846
		else
			local ifname="$dev"
		fi
847

848
849
850
851
852
853
854
		uci set $conf.mesh_$counter="dev"
		uci set $conf.mesh_$counter.dev="$ifname"
		if [ -e "/sys/class/net/$dev/phy80211" ]; then
			uci set $conf.mesh_$counter.linklayer=2
		else
			uci set $conf.mesh_$counter.linklayer=1
		fi
855
856
857
858
859
860

	    if qmp_uci_test qmp.networks.bmx6_ipv4_address ; then
	      local bmx6_ipv4_netmask="$(echo $(uci get qmp.networks.bmx6_ipv4_address) | cut -s -d / -f2)"
	      local bmx6_ipv4_address="$(echo $(uci get qmp.networks.bmx6_ipv4_address) | cut -d / -f1)"
	      [ -z "$bmx6_ipv4_netmask" ] && bmx6_ipv4_netmask="32"
	      uci set $conf.general.tun4Address="$bmx6_ipv4_address/$bmx6_ipv4_netmask"
861
862
863
	      uci set $conf.tmain=tunDev
	      uci set $conf.tmain.tunDev=tmain
	      uci set $conf.tmain.tun4Address="$bmx6_ipv4_address/$bmx6_ipv4_netmask"
864

865
	    else
p4u's avatar
p4u committed
866
	      local ipv4_suffix24="$(qmp_get_id 8bit)"
867
	      local ipv4_prefix24="$(qmp_uci_get networks.bmx6_ipv4_prefix24)"
868
869
870
871
	      if [ $(echo -n "$ipv4_prefix24" | tr -d [0-9] | wc -c) -lt 2 ]; then
	      	ipv4_prefix24="${ipv4_prefix24}.0"
	      fi
	      uci set $conf.general.tun4Address="$ipv4_prefix24.$ipv4_suffix24/32"
872
873
874
	      uci set $conf.tmain=tunDev
	      uci set $conf.tmain.tunDev=tmain
	      uci set $conf.tmain.tun4Address="$ipv4_prefix24.$ipv4_suffix24/32"
875

876
877
878
879
880
881
882
883
884
885
	    fi
	    counter=$(( $counter + 1 ))
         fi

       done
    done
  fi


  if qmp_uci_test qmp.networks.bmx6_ripe_prefix48 ; then
886
    uci set $conf.general.tun6Address="$(uci get qmp.networks.bmx6_ripe_prefix48):$device_id:0:0:0:1/64"
887
888
    uci set $conf.tmain=tunDev
    uci set $conf.tmain.tunDev=tmain
889
    uci set $conf.tmain.tun6Address="$(qmp_uci_get networks.bmx6_ripe_prefix48):$device_id:0:0:0:1/64"
890
891
  fi

892
  qmp_configure_bmx6_gateways
893
894
895
896
897

  uci commit $conf
#  /etc/init.d/$conf restart
}

p4u's avatar
p4u committed
898
qmp_restart_firewall() {
899
900
901
	iptables -F
	iptables -F -t nat
	sh /etc/firewall.user
p4u's avatar
p4u committed
902
}
903
904

qmp_check_force_internet() {
905
906
	[ "$(qmp_uci_get networks.force_internet)" == "1" ] && qmp_gw_offer_default
	[ "$(qmp_uci_get networks.force_internet)" == "0" ] && qmp_gw_search_default
907
908
}

909
qmp_configure_initial() {
910
	qmp_hooks_exec firstboot
911
912
	qmp_configure_wifi_initial
	qmp_configure_wifi
913
	/etc/init.d/network reload
914
	sleep 1
915
916
917
	qmp_configure_smart_network
}

918
qmp_configure() {
919
  qmp_configure_system
920
  qmp_set_services
921
  qmp_hooks_exec preconf
922
923
924
925
  qmp_check_force_internet
  qmp_configure_network
  qmp_configure_bmx6
  qmp_configure_lan_v6
926
  qmp_hooks_exec postconf
927
}