Developing lightweight computation at the DSG edge

qmp_functions.sh 23.9 KB
Newer Older
1
#!/bin/sh
2
# requires ip ipv6calc awk sed grep
3
4
5
6
7
8
QMP_PATH="/etc/qmp"
SOURCE_FUNCTIONS=1

#######################
# Importing files
######################
9
10
11
12
13
if [ -z "$SOURCE_OPENWRT_FUNCTIONS" ]
then
	. /lib/functions.sh
	SOURCE_OPENWRT_FUNCTIONS=1
fi
14
15
16
. $QMP_PATH/qmp_common.sh
[ -z "$SOURCE_GW" ] && . $QMP_PATH/qmp_gw.sh
[ -z "$SOURCE_NET" ] && . $QMP_PATH/qmp_network.sh
17
[ -z "$SOURCE_SYS" ] && . $QMP_PATH/qmp_system.sh
18
[ -z "$SOURCE_WIRELESS" ] && . $QMP_PATH/qmp_wireless.sh
19
[ -z "$SOURCE_COMMON" ] && . $QMP_PATH/qmp_common.sh
20
21
22

qmp_get_llocal_for_dev() {
  local dev=$1
23
  ip a show dev $dev | awk '/inet6/{print $2}'
24
25
26
27
28
}

# returns primary device
qmp_get_primary_device() {
  local primary_mesh_device="$(uci get qmp.node.primary_device)"
29
  [ -z "$primary_mesh_device" ] &&
30
31
32
33
34
35
      {
      if ip link show dev eth0 > /dev/null; then
        primary_mesh_device="eth0"
      else
        primary_mesh_device="$(ip link show | awk '!/lo:/&&/^[0-9]?:/{sub(/:$/,"",$2); print $2; exit}')"
      fi
36
      [ -z "$primary_mesh_device" ] && echo "CRITICAL: No primary network device found, please define qmp.node.primary_device"
37
38
39
40
      }
  echo "$primary_mesh_device"
}

41
# check if a device exists
42
43
44
45
qmp_check_device() {
	ip link show $1 1> /dev/null 2>/dev/null
	return $?
}
46

47
48
49
50
51
52
53
# Function qmp_set_vlan()
#
# This function creates a VLAN interface on top of an interface in order to
# isolate the routing protocol traffic there:
#
#  - 802.1 VLANs are used for wireless interfaces.
#  - 802.1ad (QinQ) VLANs are used for wired devices since qMp > 3.2.1
54
qmp_set_vlan() {
55
56
57
  local iface="$1" # The physical interface
  local vid=$2     # The VLAN
  local liface=$3  # The logical interface lan/wan_X/mesh_Y
58

59
60
  echo "Setting VLAN $vid for interface $iface"
  [ -z "$iface" ] || [ -z "$vid" ] && return
61

62
  # Replace dots by underscores to use the interface name as part of another one
63
  local uiface="$(echo $iface | sed -r 's/\./_/g')"
64

65
66
67
68
	uci set network.${uiface}_${vid}=device
	local vtype=""
	# If $dev exists and is not wireless
  if [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ]; then
69
    # 802.1ad VLANs for wired interfaces
70
    uci set network.${uiface}_${vid}.type=8021ad
71
		vtype="ad"
72
		echo "VLAN $vid for interface $iface is of type 802.1ad (QinQ)"
73
  else
74
75
76
77
		# 802.1q VLANs for wireless interfaces
		uci set network.${uiface}_${vid}.type=8021q
		echo "VLAN $vid for interface $iface is of type 802.1q"
		vtype="q"
78
  fi
79

80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
	uci set network.${uiface}_${vid}.name=${uiface}_${vid}
	if [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ]; then
		# VLANs for wired interfaces are configured directly on top of the physical
		# interface (e.g. eth0.2, eth1)
		uci set network.${uiface}_${vid}.ifname=${iface}
	else
		# VLANs for wireless interfaces need to be configured on top of the
		# logical interface the radio is put in (e.g. mesh_w0 for wlan0)
		uci set network.${uiface}_${vid}.ifname='@'${liface}
	fi
	uci set network.${uiface}_${vid}.vid=${vid}

  uci set network.${uiface}_${vid}_${vtype}=interface
  uci set network.${uiface}_${vid}_${vtype}.ifname=${uiface}_${vid}
  uci set network.${uiface}_${vid}_${vtype}.proto=${none}
  uci set network.${uiface}_${vid}_${vtype}.auto=1
96
  uci commit network
97

98
99
100
101
102
103
}

qmp_get_virtual_iface() {
  local device="$1"
  local viface=""

104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
	# is lan?
	if [ "$device" == "br-lan" ]; then
		viface="lan"
		if [ ! -e "/sys/class/net/$device/phy80211" ]; then
			echo $viface
			return
		fi
  	fi

	for l in $(qmp_get_devices lan); do
		if [ "$l" == "$device" ]; then
			viface="lan"
			if [ ! -e "/sys/class/net/$device/phy80211" ]; then
				echo $viface
				return
			fi
		fi
	done
122

123
	[ ! -e "/sys/class/net/$device/phy80211" ] && [ -n "$viface" ] && { echo $viface; return; }
124

125
	# id_char is the first char of the device: [e]th0 [w]lan1a
126
	local id_char=$(echo $device | cut -c 1)
127
128
129
130
	# id_num is the number of the device: eth[0], wlan[1]a
	local id_num=$(echo $device | tr -d "[A-z]" | tr - _ | tr . _)
	# id_extra are the extra characters after the number: eth0[], wlan1[a]
	local id_extra=$(echo $device | sed -e 's/^[a-z]*[0-9]*//g')
131

132
133
134
135
136
137
138
139
	# is wan?
	for w in $(qmp_get_devices wan); do
		if [ "$w" == "$device" ]; then
			viface="wan_${id_char}${id_num}"
			echo $viface
			return
		fi
	done
140

141
142
	qmp_log "LOG: 5"
		qmp_log "Viface: $viface"
143

144
qmp_log $device $viface
145
146
147
	# is mesh?
	for w in $(qmp_get_devices mesh); do
		if [ "$w" == "$device" ]; then
148
			viface="mesh_${id_char}${id_num}${id_extra}"
149
150
151
			break
		fi
	done
152

153
	echo "$viface"
154
155
156
157
158
159
}

# arg1=<mesh|lan|wan>, returns the devices which have to be configured in such mode
qmp_get_devices() {
  local devices=""

160
  if [ "$1" == "mesh" ]; then
161
162
		devices="$(uci get qmp.interfaces.mesh_devices 2>/dev/null)"
	fi
163
164
165
166
167
168
169
170
171
172
173
174
175

  if [ "$1" == "lan" ]; then
     devices="$(uci get qmp.interfaces.lan_devices 2>/dev/null)"
  fi

  if [ "$1" == "wan" ]; then
     devices="$(uci get qmp.interfaces.wan_devices 2>/dev/null)"
  fi

  echo "$devices"
}


176
# Scan and configure the network devices (lan, mesh and wan)
177
# if $1 is set to "force", it rescan all devices
178
179
180
181
qmp_configure_smart_network() {
	echo "---------------------------------------"
	echo "Starting smart networking configuration"
	echo "---------------------------------------"
182
	local force=$1
183
184
185
186
187
	local mesh=""
	local wan=""
	local lan=""
	local dev=""
	local phydevs=""
188
	local ignore_devs=""
189
190
	local default_lan=$(qmp_get_openwrt_default_network "lan")
	local default_wan=$(qmp_get_openwrt_default_network "wan")
191

192
193
194
	[ "$force" != "force" ] && {
		ignore_devs="$(qmp_uci_get interfaces.ignore_devices)"
	}
195

196
	for dev in $(ls /sys/class/net/); do
197
		[ -e /sys/class/net/$dev/device ] || [ dev == "eth0" ] && {
198
			local id
199
			local ignore=0
200

201
			# Check if device is in the ignore list
202
203
204
205
				for id in $ignore_devs; do
					[ "$id" == "$dev" ] && ignore=1
				done

206
207
208
209
210
211
212
213
214
215
			# [Qin] The device might be a wired device (e.g. eth0) with a switch
			# and two or more virtual switched devices (e.g. eth0.1, eth0.2)
			for sdev in $(ls /sys/class/net/$dev/ | grep upper_$dev. | cut -d "_" -f2); do
				phydevs="$phydevs $sdev\n"
				ignore=1
			done

			if [ $ignore -eq 0 ]; then
				phydevs="$phydevs $dev\n"
			fi
216
		}
217
	done
218
	phydevs="$(echo -e "$phydevs" | grep -v -e ".*ap$" | sort -u | tr -d ' ' \t)"
219

220
221
222
223
224
225
	# if force is not enabled, we are not changing the existing lan/wan/mesh (only adding new ones)
	[ "$force" != "force" ] && {
		lan="$(qmp_uci_get interfaces.lan_devices)"
		wan="$(qmp_uci_get interfaces.wan_devices)"
		mesh="$(qmp_uci_get interfaces.mesh_devices)"
	}
226

227
228
	local j=0
	local mode=""
229
230
	local cnt
	local cdev
231

232
	for dev in $phydevs; do
233
		# If force is enabled, do not check if the device is already configured
234
		[ "$force" != "force" ] && {
235

236
237
			cnt=0
			# If it is already configured, doing nothing
238
			for cdev in $lan; do
239
				[ "$cdev" == "$dev" ] && cnt=1
240
			done
241
			for cdev in $mesh; do
242
				[ "$cdev" == "$dev" ] && cnt=1
243
			done
244
			for cdev in $wan; do
245
				[ "$cdev" == "$dev" ] && cnt=1
246
247
248
			done
			[ $cnt -eq 1 ] && continue
		}
249

250
251
		# If the device is not configured already, assign its role acording to
		# OpenWrt's defaults. This avoids the per-device hooks that swapped roles
252
253
254
255
256
257
258
259
260
261
262
263
264
265
		for ddev in $default_lan; do
			[ "$dev" == "$ddev" ] && {
				lan="$lan $dev"
				mesh="$mesh $dev"
				continue
			}
		done
		for ddev in $default_wan; do
			[ "$dev" == "$ddev" ] && {
				wan="$wan $dev"
				mesh="$mesh $dev"
				continue
			}
		done
266

267
268
		# if it is a wifi device (actually, if it is not a non-wifi device)
		! ( [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ] ) && {
269
270
271
272
			j=0
			while qmp_uci_test qmp.@wireless[$j]; do
				[ "$(qmp_uci_get @wireless[$j].device)" == "$dev" ] && {
					mode="$(qmp_uci_get @wireless[$j].mode)"
273
274
					( [ "$mode" == "aplan" ] || [ "$mode" == "80211s_aplan" ] || [ "$mode" == "adhoc_ap" ] ) && lan="$dev $lan"
					( [ "$mode" == "80211s" ] || [ "$mode" == "80211s_aplan" ] || [ "$mode" == "80211s_adhoc" ] || [ "$mode" == "adhoc" ] || [ "$mode" == "adhoc_ap" ] ) && mesh="$dev $mesh"
275
276
277
278
279
					break
				}
				j=$(($j+1))
			done
		} && continue
280

281
282
		# If its not wireless nor a default wan/lan, set it to mesh
		[ "$dev" != "$default_lan" ] && [ "$dev" != "$default_wan" ] && {
283
284
285
286
287
			inmesh="0"
			# A small trick to avoid duplicates when $default_xan = "eth1 eth2" (e.g., APUs)
			for mdev in $mesh; do
				[ "$mdev" == "$dev" ] && inmesh="1"
			done
288
			[ "$inmesh" == "0" ] && mesh="$dev $mesh"
289
		}
290

291
	done
292

293
	echo "Network devices found:"
294
295
296
297
	echo "- LAN $lan"
	echo "- MESH $mesh"
	echo "- WAN $wan"

298
	# Writes the devices to the config
299
300
301
	qmp_uci_set interfaces.lan_devices "$(echo $lan | sed -e s/"^ "//g -e s/" $"//g)"
	qmp_uci_set interfaces.mesh_devices "$(echo $mesh | sed -e s/"^ "//g -e s/" $"//g)"
	qmp_uci_set interfaces.wan_devices "$(echo $wan | sed -e s/"^ "//g -e s/" $"//g)"
302
	qmp_uci_set interfaces.ignore_devices "$ignore_devs"
303
304
}

305
306
307
308
309
310
311
312
313
314
qmp_get_openwrt_default_network() {
	local role=$1
	local board_file="/etc/board.json"
	local flen=$(wc -l $board_file | cut -d " " -f 1)

	[ "$role" != "lan" ] && [ "$role" != "wan" ] && return

	grep -A${flen} "network" $board_file | grep -A${flen} $role | grep -m 1 -B${flen} "}" | grep -m 1 "ifname" | cut -d ":" -f2 | sed -e 's/^[ \t]*//' | cut -d '"' -f 2
}

315
316
qmp_attach_device_to_interface() {
	local device=$1
317
	local interface=$2
318
319
	local intype="$(qmp_uci_get_raw network.$interface.type)"

320
	echo "Attaching device $device to interface $interface"
321
322

	# is it a wifi device?
323
	if qmp_uci_test wireless.$device; then
324
		qmp_uci_set_raw wireless.$device.network=$interface
325
		echo " -> $device wireless attached to $interface"
326
327

	# if it is not
328
	else
329
			if [ "$intype" == "bridge" ]; then
330
				qmp_uci_add_list_raw network.$interface.ifname=$device
331
332
				echo " -> $device attached to $interface bridge"
			else
333
				qmp_uci_set_raw network.$interface.ifname=$device
334
335
				echo " -> $device attached to $interface"
			fi
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
	fi
}

qmp_get_ip6_slow() {
  local addr_prefix="$1"
  local addr="$(echo $addr_prefix | awk -F'/' '{print $1}')"
  local mask="$(echo $addr_prefix | awk -F'/' '{print $2}')"

  echo "qmp_get_ip6_slow addr_prefix=$addr_prefix addr=$addr mask=$mask" 1>&2

  if [ -z "$mask" ] ; then
    mask="128"
  fi

  local addr_in=$addr
  local addr_out=""
  local found=0

  while ! [ -z "$addr_in" ] ; do

    addr_in=$( echo $addr_in | sed -e "s/^://g" )

    if echo "$addr_in" | grep "^:"  >/dev/null 2>&1 ; then

      if echo "$addr_in" | grep "::"  >/dev/null 2>&1 ; then
        echo "Invalid 1 IPv6 address $addr_prefix" 1>&2
        return 1
      fi

      addr_in=$( echo $addr_in | sed -e "s/^://g" )

      if [ -z "$addr_in" ] ; then
        addr_out="$addr_out::"
      else
        addr_out="$addr_out:"
      fi

    else

      local addr16="$(echo $addr_in | awk -F':' '{print $1}')"
      addr_in=$( echo $addr_in | sed -e "s/^$addr16//g" )

      if [ -z "$addr_out" ] ; then
	addr_out="$addr16"
      else
	addr_out="$addr_out:$addr16"
      fi

      if echo "$addr16" | grep '\.'  >/dev/null 2>&1 ; then
        found=$(( $found + 2 ))
      else
        found=$(( $found + 1 ))
      fi

    fi

  done

  if echo $addr_out | grep "::" >/dev/null 2>&1 && [ "$found" -lt "8" ] ; then

    local insert="0"
    for n in $( seq $found "6" ) ; do
      insert="$insert:0"
    done

    addr_out=$( echo $addr_out | sed -e "s/^::$/$insert/g" )
    addr_out=$( echo $addr_out | sed -e "s/^::/$insert:/g" )
    addr_out=$( echo $addr_out | sed -e "s/::$/:$insert/g" )
    addr_out=$( echo $addr_out | sed -e "s/::/:$insert:/g" )

  elif echo $addr_out | grep "::"  >/dev/null 2>&1 || [ "$found" != "8" ] ; then
    echo "Invalid 2 IPv6 address $addr_prefix found=$found" 1>&2
    return 1
  fi


#  echo "Correct IPv6 address $addr_prefix addr_out=$addr_out found=$found" 1>&2
  local pos=0
  addr_in=$addr_out
  addr_out=""

  while ! [ -z "$addr_in" ] ; do

    addr_in=$( echo $addr_in | sed -e "s/^://g" )

    local addr16="$( echo $addr_in | awk -F':' '{print $1}' )"
    addr_in=$( echo $addr_in | sed -e "s/^$addr16//g" )

    if echo $addr16 | grep '\.' >/dev/null 2>&1  ; then
      local ip1=$( echo $addr16 | awk -F'.' '{print $1}' )
      local ip2=$( echo $addr16 | awk -F'.' '{print $2}' )
      local ip3=$( echo $addr16 | awk -F'.' '{print $3}' )
      local ip4=$( echo $addr16 | awk -F'.' '{print $4}' )

#      echo "addr16=$addr16 ip1=$ip1 ip2=$ip2 ip3=$ip3 ip4=$ip4" 1>&2

      addr16=$( printf "%X" $(( $(( $ip1 * 0x100 )) + $ip2 )) )

      if [ -z "$ip4" ] ; then
        echo "Invalid 3 IPv6 address $addr_prefix" 1>&2
        return 1
      fi

      addr_in=$( printf "%X" $(( $(( $ip3 * 0x100 )) + $ip4 )) )$addr_in


    fi

    local prefix16
    if [ "$pos" -le "$mask" ] ; then

      if [ "$(( $pos + 16 ))" -le "$mask" ] ; then
	prefix16=$addr16
      else
	prefix16=$( printf "%X" $(( 0x$addr16 & 0xFFFF<<$(( $(( $pos + 16 )) - $mask )) )) )
      fi

    else
      prefix16="0"
    fi


    if [ -z "$addr_out" ] ; then
      addr_out="$prefix16"
    else
      addr_out="$addr_out:$prefix16"
    fi

    pos=$(( $pos + 16 ))

  done

  echo "$addr_out"
}

qmp_get_ip6_fast() {

  if ! [ -x /usr/bin/ipv6calc ] ; then
     qmp_get_ip6_slow $1
     return $?
  fi

  local addr_prefix="$1"
  local addr="$(echo $addr_prefix | awk -F'/' '{print $1}')"
  local mask="$(echo $addr_prefix | awk -F'/' '{print $2}')"

  if [ -z "$mask" ] ; then
    echo "qmp_get_ip6_fast: ERROR addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2
    return 1
    mask="128"
  fi

488
  local addr_long=$( ipv6calc -q  --in ipv6 $addr --showinfo -m 2>&1 | awk -F'=' '/IPV6=/{print $2}' )
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594

  local fake_prefix16="20a2" # original input is manipulated because ipv6calc complains about reserved ipv6 addresses
  local addr_prefix16="$(echo $addr_long | awk -F':' '{print $1}')"
  local fake_long=$( echo $addr_long | sed -e "s/^$addr_prefix16/$fake_prefix16/g" )
  local fake_out

#  echo "qmp_get_ip6_fast: begin addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2

  if [ "$mask" -ge "0" ] &&  [ "$mask" -le "112" ] && [ "$(( $mask % 16))" = "0" ]; then

    fake_out="$( ipv6calc --in ipv6 $fake_long/$mask -F --printprefix --out ipv6addr 2>/dev/null )::/$mask"

  else

    if [ "$(( $mask % 16))" != "0" ]; then
      echo "ERROR addr_prefix=$1 mask=$mask must be multiple of 16" 1>&2
      return 1
    fi

    fake_out="$( ipv6calc --in ipv6 $fake_long/128 -F --printprefix --out ipv6addr 2>/dev/null )"
  fi

  echo $fake_out | sed -e "s/^$fake_prefix16/$addr_prefix16/g"

#  echo "qmp_get_ip6_fast: return addr_prefix=$addr_prefix addr_long=$addr_long  addr=$fake_long mask=$mask" 1>&2
}

qmp_calculate_ula96() {

  local prefix=$1
  local mac=$2
  local suffix=$3

  local prefix48=$( qmp_get_ip6_fast $prefix/128 )
  local suffix48=$( qmp_get_ip6_fast $suffix/128 )

# echo "qmp_calculate_ula96 suffix48=$suffix48" 1>&2

  local mac1="$( echo $mac | awk -F':' '{print $1}' )"
  local mac2="$( echo $mac | awk -F':' '{print $2}' )"
  local mac3="$( echo $mac | awk -F':' '{print $3}' )"
  local mac4="$( echo $mac | awk -F':' '{print $4}' )"
  local mac5="$( echo $mac | awk -F':' '{print $5}' )"
  local mac6="$( echo $mac | awk -F':' '{print $6}' )"

  local p1="$( echo $prefix48 | awk -F':' '{print $1}' )"
  local p2="$( echo $prefix48 | awk -F':' '{print $2}' )"
  local p3="$( echo $prefix48 | awk -F':' '{print $3}' )"

  local s1="$( echo $suffix48 | awk -F':' '{print $7}' )"
  local s2="$( echo $suffix48 | awk -F':' '{print $8}' )"

  printf "%X:%X:%X:%X:%X:%X:%X:%X\n" 0x$p1 0x$p2 0x$p3  $(( ( 0x$mac1 * 0x100 ) + 0x$mac2 ))  $(( ( 0x$mac3 * 0x100 ) + 0x$mac4 ))  $(( ( 0x$mac5 * 0x100 ) + 0x$mac6 ))  0x$s1 0x$s2

}

qmp_calculate_addr64() {

  local prefix=$1
  local node=$2
  local suffix=$3

  local prefix48=$( qmp_get_ip6_fast $prefix/128 )
  local suffix48=$( qmp_get_ip6_fast $suffix/128 )

  local p1="$( echo $prefix48 | awk -F':' '{print $1}' )"
  local p2="$( echo $prefix48 | awk -F':' '{print $2}' )"
  local p3="$( echo $prefix48 | awk -F':' '{print $3}' )"

  local s5="$( echo $suffix48 | awk -F':' '{print $5}' )"
  local s6="$( echo $suffix48 | awk -F':' '{print $6}' )"
  local s7="$( echo $suffix48 | awk -F':' '{print $7}' )"
  local s8="$( echo $suffix48 | awk -F':' '{print $8}' )"

  printf "%X:%X:%X:%X:%X:%X:%X:%X\n" 0x$p1 0x$p2 0x$p3   0x$node   0x$s5 0x$s6 0x$s7 0x$s8

}

qmp_get_ula96() {

  local prefix=$1
  local dev_mac=$2
  local suffix=$3
  local mask=$4

  local mac=$( qmp_get_mac_for_dev $dev_mac )
  local ula96=$( qmp_calculate_ula96 $prefix $mac $suffix )

  if [ -z "$mask" ] ; then
      echo "$ula96"
  else
      echo "$ula96/$mask"
  fi
}

qmp_get_addr64() {
  local prefix=$1
  local node=$2
  local suffix=$3
  local mask=$4
  local addr64=$( qmp_calculate_addr64 $prefix $node $suffix )
  echo "$addr64/$mask"
}

qmp_configure_prepare() {
  local conf=$1
p4u's avatar
p4u committed
595
   if ! [ -f /etc/config/$conf.orig ]; then
596
597
598
599
600
601
602
603
604
605
606
607
    echo "saving original config in: /etc/config/$conf.orig"
    cp /etc/config/$conf /etc/config/$conf.orig
  fi

  uci revert $conf
  echo "" > /etc/config/$conf
}

qmp_configure_network() {

  local conf="network"

p4u's avatar
p4u committed
608
609
610
611
  echo "-----------------------"
  echo "Configuring networking"
  echo "-----------------------"

612
  qmp_configure_prepare_network $conf
613

614
  # LoopBack device
615
616
617
618
619
620
621
  uci set $conf.loopback="interface"
  uci set $conf.loopback.ifname="lo"
  uci set $conf.loopback.proto="static"
  uci set $conf.loopback.ipaddr="127.0.0.1"
  uci set $conf.loopback.netmask="255.0.0.0"

  # WAN devices
622
623
  qmp_configure_wan
  # LAN devices
624
  qmp_configure_lan
625
626
  # MESH devices
  qmp_configure_mesh
627

628
629
630
631
  uci commit
}


632
qmp_remove_qmp_bmx6_tunnels()
633
{
634
	if echo "$1" | grep -q "^qmp_"
635
636
637
	then
		uci delete bmx6.$1
	fi
638
	uci commit bmx6
639
640
641
642
643
644
}

qmp_unconfigure_bmx6_gateways()
{
	config_load bmx6
	config_foreach qmp_remove_qmp_bmx6_tunnels tunInNet
645
646
	config_foreach qmp_remove_qmp_bmx6_tunnels tunDev
	config_foreach qmp_remove_qmp_bmx6_tunnels tunIn
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
	config_foreach qmp_remove_qmp_bmx6_tunnels tunOut
}

qmp_translate_configuration()
{
	orig_config=$1
	orig_section=$2
	orig_option=$3

	dest_config=$4
	dest_section=$5
	dest_option=${6:-$orig_option}

	value="$(uci -q get $orig_config.$orig_section.$orig_option)"
	if [ -n "$value" ]
	then
		uci set $dest_config.$dest_section.$dest_option="$value"
	fi
}

qmp_add_qmp_bmx6_tunnels()
{
	local section=$1
670
	local name="$section"
671
672
	local config=bmx6
	local ignore
673
	local t
674
	config_get ignore "$section" ignore
675

676
	[ "$ignore" = "1" ] && return
677

678
679
	local type="$(qmp_uci_get_raw gateways.$name.type)"
	qmp_log Configuring gateway $name of type $type
680
	[ -z "$name" ] && name="qmp_$gateway" || name="qmp_$name"
681
682

	if [ "$type" == "offer" ]
683
	then
684
		bmx6_type=tunIn
685
		uci set $config.$name="$bmx6_type"
686
		uci set $config.$name.$bmx6_type="$name"
687
688
689
		for t in \
			network \
			bandwidth
690
		do
691
692
			qmp_translate_configuration gateways $section $t $config $name
		done
693
694
695
	else
		bmx6_type=tunOut
		uci set $config.$name="$bmx6_type"
696
		uci set $config.$name.$bmx6_type="$section"
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
		for t in \
			network \
			srcNet \
			gwName \
			minPrefixLen \
			maxPrefixLen \
			hysteresis \
			rating \
			minBandwidth \
			tableRule \
			kernel \
			boot \
			static \
			zebra \
			system \
			connect \
			rip \
			ripng \
			ospf \
			ospf6 \
			isis \
			bgp \
			babel \
			olsr \
			exportDistance \
			srcType \
			gwId \
			ipMetric
725
		do
726
			qmp_translate_configuration gateways $section $t $config $name
727
		done
728
	fi
729

730
731
732
733
734
735
	gateway="$(($gateway + 1))"
}

qmp_configure_bmx6_gateways()
{
	qmp_unconfigure_bmx6_gateways
736
	config_load gateways
737
738
	gateway=0
	config_foreach qmp_add_qmp_bmx6_tunnels gateway
739
	uci commit bmx6
740
741
}

742
743
744
745
746
747
748
749
750
751
752
753
754
755
756

qmp_configure_bmx6() {
  local conf="bmx6"

  qmp_configure_prepare $conf
  uci set $conf.general="bmx6"
  uci set $conf.bmx6_config_plugin=plugin
  uci set $conf.bmx6_config_plugin.plugin=bmx6_config.so

  uci set $conf.bmx6_json_plugin=plugin
  uci set $conf.bmx6_json_plugin.plugin=bmx6_json.so

  uci set $conf.bmx6_sms_plugin=plugin
  uci set $conf.bmx6_sms_plugin.plugin=bmx6_sms.so

757
if [ -f /lib/bmx6_topology.so ]; then
758
759
  uci set $conf.bmx6_topology_plugin=plugin
  uci set $conf.bmx6_topology_plugin.plugin=bmx6_topology.so
760
fi
761

762
763
764
765
766
767
768
769
770
  # chat file must be syncronized using sms
  cfg_sms=$(uci add $conf syncSms)
  uci set $conf.${cfg_sms}.syncSms=chat

  uci set $conf.ipVersion=ipVersion
  uci set $conf.ipVersion.ipVersion="6"

  local primary_mesh_device="$(qmp_get_primary_device)"

771
772
  local device_id=$(qmp_get_id)
	device_id="$(echo -n $device_id | tr -cd 'ABCDEFabcdef0123456789' | tail -c 4)"
773
  if qmp_uci_test qmp.interfaces.mesh_devices &&
774
  qmp_uci_test qmp.networks.mesh_protocol_vids
775

776
    then
777
778
    local counter=1

779
780
  for dev in $(qmp_get_devices mesh); do
    echo "Configuring interface $dev in BMX6"
781

782
783
    for protocol_vid in $(uci get qmp.networks.mesh_protocol_vids); do
      local protocol_name="$(echo $protocol_vid | awk -F':' '{print $1}')"
784

785
786
787
788
789
790
      if [ "$protocol_name" = "bmx6" ] ; then
        # Check if the current device is configured as no-vlan
        local use_vlan=1
        for no_vlan_int in $(qmp_uci_get interfaces.no_vlan_devices); do
          [ "$no_vlan_int" == "$dev" ] && use_vlan=0
        done
791

792
793
794
        # Check if the protocol has VLAN tag configured
        local vid="$(echo $protocol_vid | awk -F':' '{print $2}')"
        [ -z "$vid" -o $vid -lt 1 ] && use_vlan=0
795

796
797
798
        # Check if the protocol has VLAN tag configured
        local vid="$(echo $protocol_vid | awk -F':' '{print $2}')"
        [ -z "$vid" -o $vid -lt 1 ] && use_vlan=0
799

800
801
802
803
804
        # If vlan tagging
        if [ $use_vlan -eq 1 ]; then
          # For interfaces like eth0.1, replace the dot with an underscore
          local viface="$(echo $dev | sed -r 's/\./_/g')"
          local ifname="${viface}_${vid}"
805

806
	# If not vlan tagging
807
808
809
		else
			local ifname="$dev"
		fi
810

811
812
813
814
815
		# If the interface is in the LAN bridge (br-lan) and does not use VLANed mesh, add the bridge instead
		if [ $(qmp_get_virtual_iface $dev) == "lan" ] && [ $use_vlan == "0" ]; then
			ifname="br-lan"
		fi

816
817
		uci set $conf.mesh_$counter="dev"
		uci set $conf.mesh_$counter.dev="$ifname"
818
		if [ -e "/sys/class/net/$dev" ] && [ ! -e "/sys/class/net/$dev/phy80211" ]; then
819
			uci set $conf.mesh_$counter.linklayer=1
820
821
		else
			uci set $conf.mesh_$counter.linklayer=2
822
		fi
823
824
825
826
827
828

	    if qmp_uci_test qmp.networks.bmx6_ipv4_address ; then
	      local bmx6_ipv4_netmask="$(echo $(uci get qmp.networks.bmx6_ipv4_address) | cut -s -d / -f2)"
	      local bmx6_ipv4_address="$(echo $(uci get qmp.networks.bmx6_ipv4_address) | cut -d / -f1)"
	      [ -z "$bmx6_ipv4_netmask" ] && bmx6_ipv4_netmask="32"
	      uci set $conf.general.tun4Address="$bmx6_ipv4_address/$bmx6_ipv4_netmask"
829
830
831
	      uci set $conf.tmain=tunDev
	      uci set $conf.tmain.tunDev=tmain
	      uci set $conf.tmain.tun4Address="$bmx6_ipv4_address/$bmx6_ipv4_netmask"
832

833
	    else
p4u's avatar
p4u committed
834
	      local ipv4_suffix24="$(qmp_get_id 8bit)"
835
	      local ipv4_prefix24="$(qmp_uci_get networks.bmx6_ipv4_prefix24)"
836
837
838
839
	      if [ $(echo -n "$ipv4_prefix24" | tr -d [0-9] | wc -c) -lt 2 ]; then
	      	ipv4_prefix24="${ipv4_prefix24}.0"
	      fi
	      uci set $conf.general.tun4Address="$ipv4_prefix24.$ipv4_suffix24/32"
840
841
842
	      uci set $conf.tmain=tunDev
	      uci set $conf.tmain.tunDev=tmain
	      uci set $conf.tmain.tun4Address="$ipv4_prefix24.$ipv4_suffix24/32"
843

844
845
846
847
848
849
850
851
852
853
	    fi
	    counter=$(( $counter + 1 ))
         fi

       done
    done
  fi


  if qmp_uci_test qmp.networks.bmx6_ripe_prefix48 ; then
854
    uci set $conf.general.tun6Address="$(uci get qmp.networks.bmx6_ripe_prefix48):$device_id:0:0:0:1/64"
855
856
    uci set $conf.tmain=tunDev
    uci set $conf.tmain.tunDev=tmain
857
    uci set $conf.tmain.tun6Address="$(qmp_uci_get networks.bmx6_ripe_prefix48):$device_id:0:0:0:1/64"
858
859
  fi

860
  qmp_configure_bmx6_gateways
861
862
863
864
865

  uci commit $conf
#  /etc/init.d/$conf restart
}

p4u's avatar
p4u committed
866
qmp_restart_firewall() {
867
868
869
	iptables -F
	iptables -F -t nat
	sh /etc/firewall.user
p4u's avatar
p4u committed
870
}
871
872

qmp_check_force_internet() {
873
874
	[ "$(qmp_uci_get networks.force_internet)" == "1" ] && qmp_gw_offer_default
	[ "$(qmp_uci_get networks.force_internet)" == "0" ] && qmp_gw_search_default
875
876
}

877
qmp_configure_initial() {
878
	qmp_hooks_exec firstboot
879
880
	qmp_configure_wifi_initial
	qmp_configure_wifi
881
	/etc/init.d/network restart
882
	/etc/init.d/network reload
883
	sleep 1
884
885
886
	qmp_configure_smart_network
}

887
qmp_configure() {
888
  qmp_configure_system
889
  qmp_set_services
890
  qmp_hooks_exec preconf
891
892
893
894
  qmp_check_force_internet
  qmp_configure_network
  qmp_configure_bmx6
  qmp_configure_lan_v6
895
  qmp_hooks_exec postconf
896
}