Developing lightweight computation at the DSG edge

Skip to content

GitLab

Commit 0c19540e authored by p4u's avatar p4u
Browse files

Adapt some functions to the new mode adhoc_ap

parent 05b45d68
Hide whitespace changes
Inline Side-by-side
packages/qmp-system/files/etc/qmp/qmp_functions.sh
View file @ 0c19540e
......@@ -168,18 +168,30 @@ qmp_get_devices() {
qmp_get_rescue_ip() {
local device=$1
local mac=""
[ -z "$device" ] && return 1
local rprefix=$(uci get qmp.networks.rescue_prefix24 2>/dev/null)
local rprefix=$(qmp_uci_get networks.rescue_prefix24 2>/dev/null)
[ -z "$rprefix" ] && return 0
# if device is virtual, get the ifname
if qmp_uci_test network.$device.ifname; then
device="$(uci get network.$device.ifname | tr -d @)"
local devvirt="$(qmp_uci_get_raw network.$device.ifname | tr -d @)"
device=${devvirt:-$device}
fi
local mac=$(ip addr show dev $device | grep -m 1 "link/ether" | awk '{print $2}')
[ -z "$mac" ] && return 2
# is it a wireless device?
if qmp_uci_test wireless.$device.device; then
local radio="$(qmp_uci_get_raw wireless.$device.device)"
mac=$(qmp_uci_get_raw wireless.$radio.macaddr)
else
mac=$(ip addr show dev $device | grep -m 1 "link/ether" | awk '{print $2}')
fi
[ -z "$mac" ] && {
qmp_log Warning: MAC for $device cannot be found, using 55:55:55:55:55:55 for rescue IP
mac="55:55:55:55:55:55"
}
#local xoctet=$(printf "%d\n" 0x$(echo $mac | cut -d: -f5))
local yoctet=$(printf "%d\n" 0x$(echo $mac | cut -d: -f6))
......@@ -192,33 +204,22 @@ qmp_attach_device_to_interface() {
local device=$1
local conf=$2
local interface=$3
# local intype="$(qmp_uci_get_raw network.$interface.type)" <-- does not work ¿?
local intype="$(qmp_uci_get_raw $conf.$interface.type)"
echo "Attaching device $device to interface $interface"
devcl="$(echo $device | cut -d- -f1)" # wlan0-1 -> wlan0
local wifi_config="$(uci -qX show wireless | sed -n -e "s/wireless\.\([^\.]\+\)\.device=$devcl/\1/p")"
# is it a wifi device?
if [ -n "$wifi_config" -a $(echo $(qmp_uci_get_raw wireless.$devcl) | grep -c wifi) -ge 1 ]; then
wifidev_i="$(echo $device | tr -d [A-z] | cut -d- -f2)" # wlan0-1 -> 1
wifidev_i=${wifidev_i:-0}
id="0"
for wc in $wifi_config ; do
if [ "$id" = "$wifidev_i" ]; then
echo " -> wireless.$wc attached to $interface"
uci set wireless.$wc.network="$interface"
uci commit wireless
fi
id=$(($id+1))
done
if qmp_uci_test wireless.$device; then
qmp_uci_set_raw wireless.$device.network="$interface"
uci commit wireless
echo " -> $device wireless attached to $interface"
# if it is not
else
if [ "$interface" == "lan" ]; then
uci add_list $conf.$interface.ifname="$device"
if [ "$intype" == "bridge" ]; then
qmp_uci_add_list_raw $conf.$interface.ifname="$device"
echo " -> $device attached to $interface bridge"
else
uci set $conf.$interface.ifname="$device"
qmp_uci_set_raw $conf.$interface.ifname="$device"
echo " -> $device attached to $interface"
fi
fi
......@@ -585,7 +586,7 @@ qmp_configure_rescue_ip_device()
elif qmp_is_in "$dev" $(qmp_get_devices mesh) && [ "$dev" != "br-lan" ]
then
# If it is only mesh device
qmp_configure_rescue_ip $dev
qmp_configure_rescue_ip $dev
qmp_attach_device_to_interface $dev $conf $viface
fi
}
......@@ -593,8 +594,9 @@ qmp_configure_rescue_ip_device()
qmp_configure_prepare() {
local conf=$1
echo "configuring /etc/config/$conf"
echo "-----------------------"
echo "Configuring networking"
echo "-----------------------"
if ! [ -f /etc/config/$conf.orig ]; then
echo "saving original config in: /etc/config/$conf.orig"
......@@ -613,7 +615,7 @@ qmp_configure_network() {
qmp_configure_prepare $conf
if qmp_uci_test qmp.interfaces.mesh_devices && qmp_uci_test qmp.networks.mesh_protocol_vids && qmp_uci_test qmp.networks.mesh_vid_offset; then
local vids="$(uci -q get qmp.networks.mesh_protocol_vids | awk -F':' -v RS=" " '{print $2 + '$(uci -q get qmp.networks.mesh_vid_offset)'}')"
local vids="$(qmp_uci_get networks.mesh_protocol_vids | awk -F':' -v RS=" " '{print $2 + '$(uci -q get qmp.networks.mesh_vid_offset)'}')"
fi
if [[ -n "$vids" ]] && qmp_is_routerstationpro ; then
......@@ -622,7 +624,7 @@ qmp_configure_network() {
elif qmp_uci_test qmp.interfaces.configure_switch ; then
local switch_device="$(uci get qmp.interfaces.configure_switch)"
local switch_device="$(qmp_uci_get interfaces.configure_switch)"
uci set $conf.$switch_device="switch"
uci set $conf.$switch_device.enable="1"
......@@ -683,7 +685,7 @@ qmp_configure_network() {
local LSB_PRIM_MAC="$(qmp_get_mac_for_dev $primary_mesh_device | awk -F':' '{print $6}' )"
if qmp_uci_test qmp.node.community_node_id; then
community_node_id="$(uci get qmp.node.community_node_id)"
community_node_id="$(qmp_uci_get node.community_node_id)"
elif ! [ -z "$primary_mesh_device" ] ; then
community_node_id=$LSB_PRIM_MAC
fi
......@@ -692,12 +694,12 @@ qmp_configure_network() {
# If it is enabled, apply the non-overlapping DHCP-range preset policy
LAN_MASK="$(uci get qmp.networks.lan_netmask)"
LAN_ADDR="$(uci get qmp.networks.lan_address)"
LAN_MASK="$(qmp_uci_get networks.lan_netmask)"
LAN_ADDR="$(qmp_uci_get networks.lan_address)"
START=2
LIMIT=253
if [ $(uci get qmp.non_overlapping.ignore) -eq 0 ]; then
if [ $(qmp_uci_get non_overlapping.ignore) -eq 0 ]; then
LAN_MASK="255.255.0.0"
# Last byte of lan adress must be "1" to avoid overlappings
LAN_ADDR=$(echo $LAN_ADDR | sed -e 's/\([0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\)\.[0-9]\{1,3\}/\1.1/1')
......@@ -705,14 +707,14 @@ qmp_configure_network() {
OFFSET=0
NUM_GRP=256
UCI_OFFSET="$(uci get qmp.non_overlapping.dhcp_offset)"
UCI_OFFSET="$(qmp_uci_get non_overlapping.dhcp_offset)"
[ $UCI_OFFSET -lt $NUM_GRP ] && OFFSET=$UCI_OFFSET
START=$(( 0x$community_node_id * $NUM_GRP + $OFFSET ))
LIMIT=$(( $NUM_GRP - $OFFSET ))
uci set dhcp.lan.leasetime="$(uci get qmp.non_overlapping.qmp_leasetime)"
uci set dhcp.lan.leasetime="$(qmp_uci_get non_overlapping.qmp_leasetime)"
fi
uci set dhcp.lan.start=$START
......@@ -720,7 +722,7 @@ qmp_configure_network() {
local disable_dhcp=0
if qmp_uci_test qmp.networks.disable_lan_dhcp; then
disable_dhcp="$(uci get qmp.networks.disable_lan_dhcp)"
disable_dhcp="$(qmp_uci_get networks.disable_lan_dhcp)"
fi
if [ "$disable_dhcp" != "1" ]; then
......@@ -742,29 +744,32 @@ qmp_configure_network() {
uci set $conf.lan.proto="static"
uci set $conf.lan.ipaddr=$LAN_ADDR
uci set $conf.lan.netmask=$LAN_MASK
uci set $conf.lan.dns="$(uci get qmp.networks.dns)"
uci set $conf.lan.dns="$(qmp_uci_get networks.dns)"
fi
# MESH DEVICES CONFIGURATION
local counter=1
if uci get qmp.interfaces.mesh_devices && uci get qmp.networks.mesh_protocol_vids && uci get qmp.networks.mesh_vid_offset; then
if qmp_uci_test qmp.interfaces.mesh_devices &&
qmp_uci_test qmp.networks.mesh_protocol_vids &&
qmp_uci_test qmp.networks.mesh_vid_offset; then
for dev in $(qmp_get_devices mesh); do
# If dev is empty, nothing to do
[ -z "$dev" ] || ! qmp_check_device $dev && continue
[ -z "$dev" ] && continue
# Let's configure the mesh device
echo "Configuring "$dev" for Meshing"
# Check if the current device is configured as no-vlan
local use_vlan=1
for no_vlan_int in $(uci get qmp.interfaces.no_vlan_devices 2>/dev/null); do
for no_vlan_int in $(qmp_uci_get interfaces.no_vlan_devices 2>/dev/null); do
[ "$no_vlan_int" == "$dev" ] && use_vlan=0
done
local protocol_vids="$(uci get qmp.networks.mesh_protocol_vids 2>/dev/null)"
local protocol_vids="$(qmp_uci_get qmp.networks.mesh_protocol_vids 2>/dev/null)"
[ -z "$protocol_vids" ] && protocol_vids="olsr6:1 bmx6:2"
for protocol_vid in $protocol_vids; do
......@@ -772,7 +777,7 @@ qmp_configure_network() {
# Calculating the VID offset for VLAN tag
local protocol_name="$(echo $protocol_vid | awk -F':' '{print $1}')"
local vid_suffix="$(echo $protocol_vid | awk -F':' '{print $2}')"
local vid_offset="$(uci get qmp.networks.mesh_vid_offset)"
local vid_offset="$(qmp_uci_get networks.mesh_vid_offset)"
local vid="$(( $vid_offset + $vid_suffix ))"
# virtual interface
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment